Toshiba TLP510U, TLP511E, TLP510E, TLP511U manual Drive System Control Process, Various Display Modes

Page 18

5-12. Drive System Control Process

In the drive system control process, the control signal is supplied to each kind of drive system process ICs shown in the the table below.

Table 5-12-1 shows each kind of the drive system IC

control.

Table 5-12-1 Each kind of the drive system IC control

Part No.

Type name

Process

Q701

M62399FP

Process relative to R drive

(Custom: $90)

 

 

Q702

M62399FP

Process relative to G drive

(Custom: $92)

 

 

Q703

M62399FP

Process relative to B drive

(Custom: $94)

 

 

Q704

M62399FP

Process relative to VCOM, NR

(Custom: $96)

 

 

Q705

M62399FP

Process relative to NR, Bias

(Custom: $98)

 

 

 

 

 

5-13. Various Display Modes

In this system, various LED display patterns are provided in relation to the display modes shown in Table 5-8-1. Operation processes from the status of AC cord plugged to that of power on and power off will be given below.

(1)Data of the non-volatile memory are checked when the AC cord is plugged, and all the LED are turned on in red in the initial use. In second or later use, all the LEDs are turned on in green and the unit enters the standby status.

(2)In the standby status, only the ON/STANDBY LED is turned on in orange, and the main power is off and the lamp power is also off.

(3)When the power is on by pressing the ON/ STANDBY key, the unit enters a normal status in passing through following processes.

1)The main power is on, and ON/STANDBY LED turns on in green.

2)The fan power is on, and the fan starts to rotate.

3)The lamp power is on, and LAMP LED blinks in green for about 3s.

4)With the lamp turned on, LAMP LED turns on in green and the unit enters the normal status.

(4)If the lamp does not turn on, ON/STANDBY LED turns on in orange, and the LAMP LED blinks in green for about 1 min. and then the unit returns to the standby status.

(5)In the normal status, ON/STANDBY LED and the LAMP LED are turned on in green, and the main power and the lamp power are turned on.

(6)When the power is turned off by pressing the ON/ STANDBY key, the unit enters the standby status in passing through following processes.

1)When the lamp power is turned off, ON/ STANDBY LED turns on in orange.

2)The LAMP LED blinks in green for about 1 min. For this period the lamp can not be turned on again by the ON/STANDBY key.

3)When blinking of the LAMP LED stops, only the ON/STANDBY LED turns on in orange. After this, the lamp can be turned on again by the ON/STANDBY key.

(7)Moreover, the fan works for about 2 min. to lower temperature of the unit. When the main power turns off, the fan also stops and returns to the standby status.

(8)If an error occurs due to some causes, the ON/ STANDBY LED turns on in red, and the error information is kept in the display status of the LAMP and TEMP LEDs. When the error is detected, the unit enters the standby status after cooling down process for about 2 min. In this case, if the error status continues, the error display is also kept and any key entry is not accepted.

5-7

Image 18
Contents TLP511U TLP510U TLP511E TLP510E Contents Description Main Power Supply CircuitVoltage Switching Output ControlOver-current Protection Overheat ProtectionSupplement Lamp Power Supply Circuit Lamp Driver ConfigurationOptical System Name DescriptionXGA 1.3 inch 3 plates system G.B. Drive Circuit Outline1st frame 2nd lineBasic Component Outline of Liquid Crystal Panel Basic specificationOperation Description 1 Terminal description2 Input terminal function description Name FunctionMicroprocessor System Outline1 System block diagram System Microprocessor 1 Terminal functions of the system microprocessorNon-volatile Memory Control Process Power Supply Reset ProcessRemote Control Reception Process RS-232C Transmission/Reception Process1 Contents of the status display signals and the logic Status Display ProcessOn-screen Display Process I2C control for each kind of video system Video System Control ProcessPanel System Control Process 11-1 IC control for each kind of panel systemDrive System Control Process Various Display Modes12-1 Each kind of the drive system IC control Applicable Signal 14-1 Applicable signalRS-232C Control Method 15-1 RS-232C connection signalsPin No Signal name Signal content 15-2 RS-232C communication conditions15-3 RS-232C command list Command ContentDigital Circuit Conv Forc ExchangeSignal Format Measurement Video Signal Format ConversionPanel Driving Timing Signal Generation PLL CircuitPLL IC CXA3106Q QX028 for RGB Signals Each IC DescriptionSync Process IC SYG QX004 PLL IC TLC2932 QX029 for Video SignalTiming Signal Generation PLD QX009 5. A/D Converter CXA3026Q QX201, QX401 and QX601INV 9. D/A Converter Picture Size of View Conversion IC T-FORCQX204, QX404, QX604 MemoryVideo Circuit Circuit Component1 Block diagram Audio Signal Input Signal Switch SectionVideo Signal RGB Signal2 Internal block diagram of CXA1855Q Video Demodulation Block 1 Terminal function of TC9090AN1. Y/C Separation Circuit 4 Pin configuration of TDA9141 Video/Color CircuitLuminance Y Signal Process Circuit Pin No Name FunctionPin Name Function Color Signal Process CircuitPicture Sharpness Correction Circuit SDA9 Block diagram of TDA4672 RGB Demodulation 4 Terminal function of TDA4780 12 Audio circuit block diagram Audio CircuitRGB Signal Switch Circuit output terminal for SYNC/G Sync Signal Process CircuitRGB Signal Amplifier Section VIDEO/VD TC7S08FMicroprocessor Interface QB012 M52347FP Input status QB025 CXA1315M HD. COMP. POS NON VD POS VD NEG HD. COMP. NEG HD. HD. CompNON VD POS VD NEG CCD and Drive Circuit Video Signal Process CircuitPower Supply Circuit Pre-amp and AD Coversion Circuit1 CCD camera circuit block diagram Coil Terminal Turns Winding specificationOperating Description WindingTroubleshooting Fluorescent does not turn onToshiba America Consumer PRODUCTS, INC