Toshiba 65HM117, 57HM117 manual Programming the remote control to control your other devices

Page 26
While holding down E, press the Channel Number buttons to enter the 3-digit code for your device.

57HM117_EN.book Page 26 Friday, March 23, 2007 9:48 AM

Chapter 3: Using the remote control

Programming the remote control to control your other devices

Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps below. For details on using the remote control to operate the device, see page 24.

1 In the remote control code table (- page 27), find the code for your device. If more than one code is listed, try each one separately until you find one that works.

2 Set the MODE SELECT switch to the type of device you are programming the remote control to operate — CABLE/SAT (for a cable converter box or satellite receiver), AUX 1 (for a VCR or TV/VCR combo), or AUX 2 (for a DVD player or HTIB [home theater in a box]).

3

4 To test the code, turn on the device, point the remote control at it, and press p. See notes below.

5

6

•If the correct code was entered, the device will turn off.

•If the device does not respond, repeat steps 1–4 using another code.

•If the device does not respond to another code, you will need to use the remote control that came with the device.

Remember to set the MODE SELECT switch back to “TV” to control the TV.

For future reference, write down the code(s) you used:

DEVICE CODE

DEVICE CODE

Note:

•In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

•Every time you change the batteries, you will need to reprogram the remote control.

•Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

26

HM117 (E/F) Web 213:276

Page 25 Page 27
Image 26
Page 25 Page 27
Contents
57HM117 65HM117 Safety Precautions Dear CustomerAdditional Safety Precautions Important Safety InstructionsInstallation, Care, and Service InstallationService CarePart Trademark Information Voice announce featureImportant notes about your DLP projection TV Contents Index Welcome to Toshiba Features of your new TVIntroduction DeathIntroduction HD1, ColorStream HD2, Hdmi 1, Hdmi 2, Hdmi 3, PC TV front and side panel controls and connectionsBlue, Yellow, and Green/Red Control panelTV back panel connections ColorStream HD-1 and ColorStream HD-2About the connection illustrations Connecting your TVOverview of cable types You will need Connecting a VCR and antenna or Cable TV no Cable boxTo view the antenna or Cable signal To view the VCRCoaxial cables Video cable Connecting a VCR with S-video and a cable boxTo view basic and premium Cable channels Standard audio cablesTo view the VCR or view and record antenna channels To view antenna or Cable channelsTo view the DVD player To record a TV program while watching a DVDIf you cannot locate the device’s infrared sensor To connect the IR blaster cableTo control the devices Select the Video 2 video input source on the TV Connecting a camcorderTo view the camcorder video To view the Hdmi device video Connecting an Hdmi or DVI device to the Hdmi inputTo connect an Hdmi device, you will need To connect a DVI device, you will needConnecting an audio system To control the audioTo connect a PC to the PC in terminal on the TV Connecting a personal computer PCFormat Resolution Frequency To connect a PC to the Hdmi terminal on the TV Installing the remote control batteries Using the remote control Preparing the remote control for use Remote control effective rangeLearning about the remote control TheaterWide 1/2/3, Full, and 43 HDVCR, set the Mode Select switch to AUX Using the remote control to control your other devicesTo use your TV remote control to operate a DVD player or HTIB, set the Mode Select switch toRemote Control functional key chart AUX 1 VCRProgramming the remote control to control your other devices TV/VCR Combo Cable converter boxSatellite receiver DVD/VCR ComboHtib Icon Option Menu layout and navigationMain menu layout Installation Setup/Installation menu layoutSetup menu Navigating the menu systemSelecting the menu language Setting up your TVTo configure the ANT input source To select the menu languageTo program channels automatically Programming channels automaticallyManually adding and deleting channels in the channel memory To add or delete channels in the channel memoryLabeling channels To create and assign a custom label Setting the Hdmi audio modeTo set the Hdmi audio mode To delete the custom labelTo view the digital signal meter Viewing the digital signal meterTo set the Power-On Mode feature To close the screen and return to the Terrestrial menuTo cancel the reset To close the screen and return to the Installation menuReset Factory Defaults Viewing the system statusLabeling the video input sources Using the TV’s featuresSelecting the video input source to view To select the video input source to viewFavorites Browser Tuning channelsTuning channels using Channel Browser Elements of the Channel Browser Adding and clearing channels and inputs in the History ListSwitching between two channels using SurfLock Tuning to a specific channel programmed or unprogrammedSwitching between two channels using Channel Return TheaterWide 1 picture size for 43 format programs Selecting the picture sizeNatural picture size TheaterWide 2 picture size for letter box programsTo set the scroll settings Full picture size for 169 480i, 480p source programs onlyTo set the Cinema Mode to Film To turn on the auto aspect ratio featureTo turn off the auto aspect ratio feature To set the Cinema Mode to VideoAdjusting the picture quality Adjusting the pictureSelecting the picture mode Base closed captions Using the closed caption modeDigital CC Settings To view captions or textCC Selector Adjusting the audioUsing the digital audio selector Muting the soundSelecting stereo/SAP broadcasts Adjusting the audio qualityTo adjust the audio quality To listen to stereo soundUsing the StableSound feature Using the Dolby Digital Dynamic Range Control featureIf you cannot remember your PIN code Using the Locks menuEntering the PIN code Changing your PIN codeTo block and unblock TV programs and movies Press b to highlight Enable Rating BlockingBlocking TV programs and movies by rating V-Chip To download the additional rating system if availableTo unblock individual channels Blocking channelsTo block channels Using the input lock feature Unlocking programs temporarilyTo adjust the PC settings Using the PC settings featureUsing the control panel lock feature To lock the control panelSetting the PC Audio Setting the sleep timerTo display TV status information using Recall Understanding the auto power off featureUnderstanding the last mode memory feature To display TV status information using InfoUsing dynamic contrast Using the TV’s advanced featuresUsing the advanced picture settings features Using the static gamma featureTo select the color temperature Selecting the color temperatureSelecting the lamp mode To select the lamp modeCableClear field, select your desired setting Using Mpeg noise reductionTo change the CableClear settings To select the Mpeg noise reduction levelUsing the SRS WOW surround sound feature Using the advanced audio settings featuresUsing the Game Mode feature Troubleshooting General troubleshootingClosed caption problems Remote control problemsChannel tuning problems Rating blocking V-Chip problemsLED Indication Condition Solution Voice Announce LED indicationsAppendix Lamp unit replacement and careWhen to replace the lamp unit CanadaHow to replace the lamp unit Required toolsReplace the screw and tighten using a manual screwdriver Disposing of the used lamp unitSpecifications Pin No Signal nameLimited United States Warranty For DLP Television ModelsLimited Canadian Warranty For Toshiba Brand DLP Television ModelsArbitration and Dispute Resolution 57HM117EN.book Page 70 Friday, March 23, 2007 948 AM Index Programming57HM117EN.book Page 72 Friday, March 23, 2007 948 AM 57HM117EN.book Page 73 Friday, March 23, 2007 948 AM 07-04
Top Page Image Contents