Toshiba 65HM117, 57HM117 Programming channels automatically, To program channels automatically

Page 32

57HM117_EN.book Page 32 Friday, March 23, 2007 9:48 AM

Chapter 5: Setting up your TV

Programming channels into the TV’s channel memory

When you press <or ,on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory.

Follow the steps below to program channels into the TV’s channel memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory.

Note:

•You must configure the antenna input source before programming channels (- page 31).

•If the Antenna input signal type is set to Cable, the automatic channel programming process erases channels that were previously programmed into the TV’s memory.

•If the Antenna input signal type is set to Antenna, the automatic channel programming process adds newly found channels to the existing set of programmed channels (and does NOT erase channels that were previously programmed into the TV’s memory.) To remove an Antenna source channel from the memory, you must manually delete it.

•To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

•Programming channels when the antenna input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly.

To program channels automatically:

1 Configure the antenna input source, if you have not already done so (- page 31).

2 Press Yand open the Setup menu.

3 Highlight Installation and press T.

Setup

Installation

Sleep Timer

PC Settings

Power-On Mode

Fast

4 (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrial menu, highlight Channel Program to bring up the Start, and press T again to begin channel programming.

Installation

Terrestrial

 

Input Configuration

 

 

 

Channel Program

 

Start

 

Channel Add/Delete

 

 

 

 

 

 

 

Signal Meter

 

 

 

 

 

 

 

 

 

 

 

 

ANT Cable

Scanning channels, please wait ...

52%

Number of Channels Found - 73

Scanning Digital Channels

Found Channel - 118

Abort

The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above).

5 To cancel channel programming, press Oon the remote control (or highlight Abort in the on-screen display and press T).

When channel programming is finished, press <or ,to view the programmed channels.

Manually adding and deleting channels in the channel memory

After automatically programming channels into the channel memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

1 Press Yand open the Setup menu.

2 Highlight Installation and press T.

3 (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrial menu, highlight Channel Add/Delete, and then press T.

Installation

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

32

HM117 (E/F) Web 213:276

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 57HM117 65HM117 Safety Precautions Dear CustomerImportant Safety Instructions Installation, Care, and ServiceAdditional Safety Precautions InstallationService CarePart Trademark Information Voice announce featureImportant notes about your DLP projection TV Contents Index Features of your new TV IntroductionWelcome to Toshiba DeathIntroduction TV front and side panel controls and connections Blue, Yellow, and Green/RedHD1, ColorStream HD2, Hdmi 1, Hdmi 2, Hdmi 3, PC Control panelTV back panel connections ColorStream HD-1 and ColorStream HD-2About the connection illustrations Connecting your TVOverview of cable types Connecting a VCR and antenna or Cable TV no Cable box To view the antenna or Cable signalYou will need To view the VCRConnecting a VCR with S-video and a cable box To view basic and premium Cable channelsCoaxial cables Video cable Standard audio cablesTo view antenna or Cable channels To view the DVD playerTo view the VCR or view and record antenna channels To record a TV program while watching a DVDIf you cannot locate the device’s infrared sensor To connect the IR blaster cableTo control the devices Select the Video 2 video input source on the TV Connecting a camcorderTo view the camcorder video Connecting an Hdmi or DVI device to the Hdmi input To connect an Hdmi device, you will needTo view the Hdmi device video To connect a DVI device, you will needConnecting an audio system To control the audioConnecting a personal computer PC Format Resolution FrequencyTo connect a PC to the PC in terminal on the TV To connect a PC to the Hdmi terminal on the TVUsing the remote control Preparing the remote control for useInstalling the remote control batteries Remote control effective rangeLearning about the remote control TheaterWide 1/2/3, Full, and 43 HDUsing the remote control to control your other devices To use your TV remote control to operate aVCR, set the Mode Select switch to AUX DVD player or HTIB, set the Mode Select switch toRemote Control functional key chart AUX 1 VCRProgramming the remote control to control your other devices Cable converter box Satellite receiverTV/VCR Combo DVD/VCR ComboHtib Icon Option Menu layout and navigationMain menu layout Setup/Installation menu layout Setup menuInstallation Navigating the menu systemSetting up your TV To configure the ANT input sourceSelecting the menu language To select the menu languageProgramming channels automatically Manually adding and deleting channels in the channel memoryTo program channels automatically To add or delete channels in the channel memoryLabeling channels Setting the Hdmi audio mode To set the Hdmi audio modeTo create and assign a custom label To delete the custom labelViewing the digital signal meter To set the Power-On Mode featureTo view the digital signal meter To close the screen and return to the Terrestrial menuTo close the screen and return to the Installation menu Reset Factory DefaultsTo cancel the reset Viewing the system statusUsing the TV’s features Selecting the video input source to viewLabeling the video input sources To select the video input source to viewFavorites Browser Tuning channelsTuning channels using Channel Browser Elements of the Channel Browser Adding and clearing channels and inputs in the History ListSwitching between two channels using SurfLock Tuning to a specific channel programmed or unprogrammedSwitching between two channels using Channel Return Selecting the picture size Natural picture sizeTheaterWide 1 picture size for 43 format programs TheaterWide 2 picture size for letter box programsTo set the scroll settings Full picture size for 169 480i, 480p source programs onlyTo turn on the auto aspect ratio feature To turn off the auto aspect ratio featureTo set the Cinema Mode to Film To set the Cinema Mode to VideoAdjusting the picture quality Adjusting the pictureSelecting the picture mode Using the closed caption mode Digital CC SettingsBase closed captions To view captions or textAdjusting the audio Using the digital audio selectorCC Selector Muting the soundAdjusting the audio quality To adjust the audio qualitySelecting stereo/SAP broadcasts To listen to stereo soundUsing the StableSound feature Using the Dolby Digital Dynamic Range Control featureUsing the Locks menu Entering the PIN codeIf you cannot remember your PIN code Changing your PIN codePress b to highlight Enable Rating Blocking Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies To download the additional rating system if availableTo unblock individual channels Blocking channelsTo block channels Using the input lock feature Unlocking programs temporarilyUsing the PC settings feature Using the control panel lock featureTo adjust the PC settings To lock the control panelSetting the PC Audio Setting the sleep timerUnderstanding the auto power off feature Understanding the last mode memory featureTo display TV status information using Recall To display TV status information using InfoUsing the TV’s advanced features Using the advanced picture settings featuresUsing dynamic contrast Using the static gamma featureSelecting the color temperature Selecting the lamp modeTo select the color temperature To select the lamp modeUsing Mpeg noise reduction To change the CableClear settingsCableClear field, select your desired setting To select the Mpeg noise reduction levelUsing the SRS WOW surround sound feature Using the advanced audio settings featuresUsing the Game Mode feature Troubleshooting General troubleshootingRemote control problems Channel tuning problemsClosed caption problems Rating blocking V-Chip problemsLED Indication Condition Solution Voice Announce LED indicationsLamp unit replacement and care When to replace the lamp unitAppendix CanadaHow to replace the lamp unit Required toolsReplace the screw and tighten using a manual screwdriver Disposing of the used lamp unitSpecifications Pin No Signal nameLimited United States Warranty For DLP Television ModelsLimited Canadian Warranty For Toshiba Brand DLP Television ModelsArbitration and Dispute Resolution 57HM117EN.book Page 70 Friday, March 23, 2007 948 AM Index Programming57HM117EN.book Page 72 Friday, March 23, 2007 948 AM 57HM117EN.book Page 73 Friday, March 23, 2007 948 AM 07-04

65HM117, 57HM117 specifications

The Toshiba 57HM117 and 65HM117 are part of Toshiba's line of rear projection televisions that offered consumers a compelling blend of advanced technology and large screen entertainment, ideal for movie enthusiasts and gamers alike.

One of the standout features of these models is their impressive screen size, providing a cinema-like experience right from the comfort of home. The 57HM117 comes with a screen size of 57 inches, while the 65HM117 boasts an even larger 65-inch display, making both models suitable for expansive living spaces or home theaters.

Both televisions employ Toshiba's DLP (Digital Light Processing) technology, which utilizes micro-mirrors to produce bright and sharp images. This technology is known for its ability to deliver vibrant colors and a high contrast ratio, enhancing the overall viewing experience. The 57HM117 and 65HM117 support a native resolution of 1080p, which means they can display high-definition content with remarkable clarity and detail, perfect for enjoying Blu-ray films or high-definition broadcasts.

In terms of connectivity, these models are equipped with multiple inputs, including HDMI, component, and composite connections, allowing users to easily connect a range of devices such as DVD players, gaming consoles, and streaming devices. This versatility ensures that users can enjoy a wide variety of content with ease. Additionally, they feature integrated digital tuners for access to over-the-air broadcast channels.

Another notable characteristic is Toshiba’s variable picture modes, which allow users to customize their viewing preferences depending on the content being viewed or the ambient light in the room. Options typically include settings designed for sports, movies, and standard viewing.

The design of both televisions is sleek and modern, complementing any home decor. The rear projection technology means that they can be placed close to walls, making them a suitable choice for smaller spaces without sacrificing the size of the screen.

Ultimately, the Toshiba 57HM117 and 65HM117 televisions represent a blend of innovative technology and user-friendly features, making them a strong choice for anyone looking to enhance their home entertainment experience.
Top Page Image Contents