Toshiba 62HM15A owner manual Appendix, Lamp unit replacement and care, Replacing the lamp unit

Page 103

11Appendix

Lamp unit replacement and care

Replacing the lamp unit

(User-replaceable component)

WARNING: RISK OF

ELECTRIC SHOCK!

TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death

or serious injury.

The light source for this TV is a mercury lamp with internal atmospheric pressure that increases during use. The lamp has a limited service life that varies depending on product use and user settings.

As is generally the case with all projection TVs that use projection lamps as a light source, the brightness of the lamp in this TV may vary somewhat over the expected service life and will generally decrease over time. The average useful service life for the lamp is approximately 8,000 hours in Low Power mode or 6,000 hours in High Bright mode. See “Selecting the Lamp mode” on page 75 for information on switching the lamp mode. Because these are averages, some lamps will require earlier replacement.

Note : The lamp is warranted only for the periods and to the extent set forth in the Limited Warranty applicable to this set, which is a substantially shorter period of time than the average useful service period. See “Limited United States Warranty” on page 107.

If you use the lamp beyond its service life:

you may notice a reduction in the colors and/or brightness of the picture; and

the strength of the quartz glass in the lamp will be reduced and the lamp may rupture (often making a loud noise when this happens). If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

CAUTION: Always handle the lamp unit with care.

The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional abuse (such as excessive mechanical abuse or handling by children or pets), the unit may break, exposing sharp edges or pinch points.

When to replace the lamp unit

You should replace the lamp unit:

if the picture darkens and/or colors fade;

if the screen (lamp) does not light (LED indication #3, page 99); or

if you hear a loud noise and the picture goes black, which may indicate a lamp rupture (LED indication #3, page 99).

To obtain a replacement lamp unit:

 

Web

Contact

In warranty

www.tacp.toshiba.com/service

Call toll-free

1-800-631-3811.

 

 

 

 

 

Out of

www.ceaccessories.toshiba.com

Consult your

warranty

 

consumer

 

electronics dealer

 

 

 

 

for availability.

 

 

 

Use the replacement lamp unit model listed below only. Using any other lamp may cause damage to the TV and/or lamp.

CAUTION: Always replace with same

type lamp unit: Model No. D95-LMP (Stock no. 23311153)

Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.

103

 

Downloaded from www.Manualslib.com manuals search engine

Image 103
Contents 46HM15 62HM15A 46HM15 ST4605 62HM15A ST6214 Safety PrecautionsInstallation, Care, and Service Important Safety InstructionsOn next Care from previous column Installation from previousNever attempt to service the TV yourself Service CenterContents Using the TV Guide On Screen Setting up and using TheaterNet on-screenSee Important notes about your DLP projection TV on Features of your new TVIntroduction Welcome to ToshibaSee LED indications on Green and Red LEDs Connecting your TVPower Press to turn the TV on and off TV front touchpad and side panel controls and connections7 !¡ TV back panel connectionsTo a Personal Computer PC Overview of cable typesYou will need To view encrypted digital channelsTV back panel Connecting a camcorder Connecting a VCR and antenna or Cable TV no Cable boxTo view basic and premium Cable channels Connecting a VCR and Cable boxTo view basic Cable channels and use the TV’s features On Screen recording featuresTo view the VCR or view and record antenna channels Connecting a VCR and satellite receiverOne signal splitter Four coaxial cables Select the ColorStream HD-1 video input source on the TVTo view the DVD player To view premium Cable channelsFrom antenna or Cable TV From antenna or Cable Your TV has ColorStream component video inputsTo view antenna or Cable channels To record a TV program while watching a DVDTo dub or edit from VCR 1 to VCR Connecting two VCRsSelect the ANT-1 video input source on the TV To view VCRTo connect an Hdmi device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputOne Hdmi cable type a connector per Hdmi device See Setting the Hdmi audio mode onConnecting an analog audio system Connecting a digital audio systemTo control the audio To connect the IR blaster cable TheaterNet on-screen device controlTo control the devices Using TheaterNet on-screen device control Connecting IEEE1394 video devicesUsing analog-compatible IEEE1394 devices Supported signalsIEEE1394 device initialization When you connect a D-VHS or Avhd device to the TVOn Screen interactive program guide built in to this TV To edit the IEEE1394 device information IEEE1394 device managementHighlight the device you want to edit and press Enter To connect to the G-LINK terminal LINKconnectionSee Chapter Learning about the remote control Using the remote controlKey for a function that is not available Point remote control Toward remote sensor On front of TV Remote control and the TVThere is no obstruction between To install the remote control batteries Installing the remote control batteriesDevice mode control after programming Power Remote Control functional key chartAudio VCR Mute CH y VOL y Device code setupSearching and sampling the code of a device NumbersTo reset the volume controls to the original device mode Using the volume lock featureOperational feature reset Repeatedly press Mode to select CABLE/SAT modeVCRs/PVRs Multi-brand remote control device codesCable boxes DVD players CD playersReceivers Laser disksMain menu layout Menu layout and navigationYou can use the buttons on the remote Setup / Installation menu layoutButtons yzx on the remote Control or TV front panel to move Navigating the menu systemScreen 1 Select the TV location USA, and then press Setting up the TV Guide On Screen systemTo set up the TV Guide On Screen system Screen 3 Do you have Cable service connected?For additional details, see If you select Video 1, screen 7 appearsSetting up the TV Guide On Screen system Use the x buttons to select the Setup menu If the information is incorrect, select No, repeat setupTV Guide On Screen system setup. Press Enter to When you turn on the TV. To turn off the automaticSelecting the menu language Setting up your TVConfiguring the antenna input sources To configure the ANT 1 and ANT 2 input sourcesProgramming channels automatically Programming channels into the TV’s channel memoryTo program channels automatically Manually adding and deleting channels in the channel memory Lists Programming your favorite channelsTo add and delete channels in the Favorite Channels sets To clear your favorite channelTheaterNet Setup menu opens Setting up and using TheaterNet on-screen device controlSetting up TheaterNet To set up TheaterNet device controlTo view another source Using the TheaterNet control iconsTo select the device’s control icons directly To close the on-screen control iconsMiscellaneous audio devices TheaterNet IR device codesAmplifiers Laser disk playersVCRs Video accessory Hdtv decoderBrand Setting the time and date Setting the Avhd device skip timeSetting the Hdmi audio mode To view the CableCARD menu Setting the Quick Restart FeatureTo set the Quick Restart feature Viewing the CableCARD menuViewing the system status Viewing the digital signal meterInstructions TV Guide On Screen system includes the following featuresTo open the TV Guide On Screen system Rating, stereo, HDTV, new episodeNavigating the TV Guide On Screen system TV Guide On Screen remote control functionsLock/unlock icon indicates the status of the Video Window Video WindowPanel Menus System, the current program appears in the Video WindowTV Guide On Screen Icons Info Box¥ Show is presented in high-definition TV, if available Listings screen TV Guide On Screen ServicesExample Category search Search screenTo edit or delete a keyword List of all matching shows for that keyword is displayedTo view a recording, you can do one of the following For additional details, see Record features onRecordings screen To choose the way recordings are displayedEst recording Record featuresSet a show to Record from a panel menu Schedule screenEnter to display the Record Options panel menu Don’t Record This Show-Cancels the RecordingHighlight NEW Manual Recording and press Show previously set to RecordSet a show Reminder from a panel menu Remind featuresManually set a show Reminder Reminder notification banner Change system settings Setup screenChange channel display Remind defaults Change default optionsGeneral defaults Record defaultsSource can be hidden. See page 68 for details Using the TV’s featuresSelecting the video input source to view To select the video input source to viewTo clear the input labels Labeling the video input sourcesDTV Satellite/DSS Cable Game Console To label the video input sourcesTo tune to a channel in Browse mode Tuning channelsUsing the Channel Browser To toggle between Browse mode and Select modeAdding channels to the channel history To set a channel as Home using the remote controlTo set a channel as Home using the menus To tune to the Home channelSwitching between two channels using SurfLock Tuning your favorite channelsTuning to the next programmed channel Switching between two channels using Channel ReturnTo select the picture size Selecting the picture sizeTheaterWide 2 picture size for letter box programs Scrolling the TheaterWide picture onNone of the picture is hidden TheaterWide 1 picture size For 43 format programTo turn off the auto aspect ratio feature Using the auto aspect ratio featureTo set the scroll settings To turn on the auto aspect ratio featureTo select the lamp mode Selecting the lamp modeTo set the Cinema Mode to Film To set the Cinema Mode to VideoTo close the POP window and tune to the highlighted window Using the POP featuresUsing the POP double-window feature To display a program in the POP windowPOP double-window aspect ratio Switching the speaker audio main or POPAspect ratio is the ratio of width to height of the picture Highlight the window for the channel you want to view Using the Freeze featureUsing the favorite channel scan feature To scan and tune your favorite channelsSelecting the picture mode Adjusting the pictureAdjusting the picture quality To select CableClear/DNR preferences Using CableClear/DNR digital noise reductionSelecting the color temperature To select the color temperatureTo select dynamic contrast preferences Using Mpeg noise reductionUsing dynamic contrast To select the Mpeg noise reduction levelAdvanced closed captions Using the closed caption modeTo select digital closed captions Digital closed captionsPress Menu and open the Applications menu Selecting stereo/SAP broadcasts Adjusting the audioUsing the digital audio selector Muting the soundUsing the sub-bass system SBS Adjusting the audio qualityUsing the StableSound feature Turning off the built-in speakers Using the SRS WOW surround sound featureSelecting the optical audio output format Memory card specifications Using the memory card Jpeg picture viewer/MP3 audio playerPress to rotate the large picture 90 clockwise Using the Jpeg picture viewerTo view digital photos on your TV Press x to rotate the large picture 90 counterclockwiseTo close the picture viewer and remove the memory card Using the MP3 audio playerTo set the slide show interval To close the picture viewerMemory card care and handling Volume, and mute buttons, and then press EnterTo close the MP3 audio player To set the sleep timer Setting the On/Off Timer Setting the sleep timerTo cancel the sleep timer Displaying the Channel Banner Understanding the auto power off featureUnderstanding the last mode memory feature Using the gray level featureChanging your PIN code Using the Locks menuEntering the PIN code If you cannot remember your PIN codeIndependent rating system for broadcasters Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies Press z to highlight Edit Rating Limits and press EnterUnlocking programs temporarily Blocking channelsLocking video inputs Using the front panel lock feature Using the GameTimerTroubleshooting V-Chip feature is available for the U.S. V-Chip system only To SAP modeClosed caption problems FeatureLED indications Setup TV Guide On Screen FAQs101 On Screen system? TV Guide On Screen FAQsReplacing the lamp unit Lamp unit replacement and careWhen to replace the lamp unit AppendixGrasp the lamp unit handle and gently pull the lamp unit How to replace the lamp unitDisposing of the used lamp unit Call Tacp Consumer Solutions atReplace the thumb screw and hand-tighten Television System SpecificationsFor DLP Television Models Limited United States Warranty108 109 Channel programming Index87Ð90 106 Picture adjustmentsPicture-out-picture POP 2Ð5Toshiba America Consumer PRODUCTS, L.L.C
Related manuals
Manual 112 pages 972 b