| 2 | Ohms | 4 Ohms | 8 Ohms |
| ||
mEQ | Ll | C l | Ll | C l | Ll | C l |
|
8 0 H z | 5.5mH | 68Oj.lF | IlmH | 33OpF | 22mH | 18O)lF |
|
IOOHz | 4.7mH | 56OpF | 9.lmH | 27OpF | 1 8 m H | 15OpF |
|
| |||||||
130Hz | 3.3mH | 4OOcF | 6.8mH | 2OOpF | 15mH | 1OObF |
|
200Hz | 2.2mH | 3OOpF | 4.7mH | 15OpF | 9.lmH | 75pF |
|
260Hz | 1.8mH | 2OOpF | 3.6mH | 1OOpF | 6.8mH | 5OpF |
|
400Hz | l . l m H | 15OpF | 2.2mH | 68pF | 4.7mH | 33pF |
|
6 0 0 H z | 0.75mH | 1oopF | 1.5mH | 47~F | 3.0mH | 26pF |
|
8 0 0 H z | 0.5mH | 68pF | l . O m H | 33lF | 2.0mH | 15pF |
|
IOOOHz | 0.47mH | 5OpF | 0.9lmH | 27pF | 1.8mH | 13~F |
|
1200Hz. | 0.33mH | 44pF | 0.75mH | 22pF | 1.5mH | IlpF |
|
1800Hz | 0.27mH | 3OpF | 0.50mH | 15pF | l . O m H | 6.8pF |
|
4000Hz | O . l O m H | 15pF | 0.22mH | 6.8pF | 0.47mH | 3.3pF |
|
AMPLIFIER LOCATiON AND MOUNTING
Soundstream Granite amplifiers employ highly efficient circuitry and a unique ChassisinkTM design to maintain lower operating temperatures. When mounting the amplifier, it should be securely attached to either a panel or to an amp board or rack that is securely fastened to the vehicle, away from moisture, stray or moving objects, and major electrical components (electrical motors, fuel pumps, etc.). To provide adequate ventilation, mount the amplifier so that there are at least two inches of freelycirculating air above and to the sides of it.
A. Using the amplifier as a template, mark the mounting surface. B. Remove the amplifier and drill the holes.
C. Mount the amplifier to the surface using the provided hardware.
WIRING
You will need the following tools for the wiring of the amplifier: Phillips or slotted screwdriver, wire strippers and wire crimpers.
When baring wires for connection to the amplifier, remove 3/8” to l/2” of the insulation. For the speaker leads, use the supplied l/4” insulated female crimp connectors and slide the connector onto the terminal on the amplifier. On the power, ground and remote connections, loosen the screws on the terminal block, slide the bared wire into the
Amplifier | up to 5’ | up to 70’ | up to 75’ | up to 20’ |
Granite 60.2 12 ga or larger 12 ga or larger 10 ga or larger 10 ga or larger
Granite 120.4 12 ga or larger 12 ga or larger 10 ga or larger 10 ga or larger
Granite 160.6 10 ga or larger 8 ga or larger 8 ga or larger 8 ga or larger
A. Carefully run the audio and remote
B. Connect the speakers as shown in “Speaker Wiring Configurations.” Use at
1 7