Parrot DMP-BD80 Changing the speaker setting to suit your speakers BD80, Delay time ms

Changing the speaker setting to suit your speakers [BD80]

When connecting to an amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on the amplifier/receiver.

The settings are effective when connecting to analog 7.1ch AUDIO OUT/5.1ch AUDIO OUT terminal.

Preparation

1Set “Analog Audio Output” to “7.1ch” or “2ch (Downmix) + 5.1ch”. ( 31)

A message is displayed.

2Press [OK].

			Center (C)
Front (L)	L	ms	C	dB	R	Front (R)
		0.0		0.0
	dB				dB
	0.0
					0.0
Complete	Complete			dB	SW	Subwoofer
Test	Test			0.0
						(SW)

LS	dB	ms	dB	RS
	0.0	0.0	0.0
LB	dB	ms	dB	RB
	0.0	0.0	0.0
(LS) Surround (RS)			(LB) Surround back(RB)§

§Surround back channel is enabled only when setting “Analog Audio Output” to “7.1ch”.

Speaker presence and size ( L C R SW LS RS LB RB )

Set all the connected speakers individually.

1Press [3, 4, 2, 1] to select the speaker icon and press [OK].

2 Press [3, 4] to select the setting and press [OK].

Delay time ( ms )

0.0

For optimum listening with 7.1/5.1-channel sound, all the speakers, except for the subwoofer, should be the same distance from the seating position.

If you have to place the center, surround and surround back speakers closer to the seating position, adjust the delay time to make up for the difference.

If either distance A or C is less than B ( below) find the difference in the relevant table and change to the recommended setting.

1Press [3, 4, 2, 1] to select the delay time box ( ms0.0 ) and press [OK].

2Press [3, 4] to select the setting and press [OK].

5.1ch speaker			7.1ch speaker connection
connection
Approximate room dimensions								: Actual
	C			C
L	C	R	L	C	R			speaker
							SW	position
	A			A				: Ideal
		B			B
		SW	LS LS		C RS	RS		speaker
								position
		C			C
								A B C
	LS	RS	LB		RB
								: Primary
	LS	RS	LB		RB			listening
Circle of constant primary listening distance								distance

Icon examples:
Surround speaker (LS)			LS		LS
≥Large:	Select when
	the speaker
		Large		Small		No
	supports
≥Small:	low-frequency (under 100 Hz) reproduction.
	Select when the speaker does not support
	low-frequency reproduction.

In order to make an ideal listening environment, settings of speaker sizes may be automatically adjusted.

For example, if the subwoofer is set to “No”, the front speakers will automatically be set to “Large”. (In this case, we recommend

ACenter speaker

Difference	Setting
Approx. 34 cm	1.0 ms
Approx. 68 cm	2.0 ms
Approx. 102 cm	3.0 ms
Approx. 136 cm	4.0 ms
Approx. 170 cm	5.0 ms

Channel balance (		)
	dB
	0.0

CSurround/Surround back speakers

Difference	Setting
Approx. 170 cm	5.0 ms
Approx. 340 cm	10.0 ms
Approx. 510 cm	15.0 ms

connecting a speaker that can reproduce bass below 100 Hz.)

1Select “Test” and press [OK].

A test signal is output.

Front (L)_—)Center (C)_—)Front (R)_—)Surround (RS)

:;

Surround (LS)(— Surround Back (LB) (— Surround Back (RB)

2While listening to the test signal, press [3, 4] to adjust the volume of each speaker

Front speakers: 0.0 to s6.0 dB

Center speaker, Surround/Surround Back speakers:

0.0to s12.0 dB

3 Press [OK].

The test signal stops.

≥No signal is output for the subwoofer. To adjust its volume, play something, then return to this screen to adjust to suit your taste.

Settings

To finish the speaker setting

Press [3, 4, 2, 1] to select “Complete” and press [OK].

RQT9401

33