Parrot DMP-BD80 operating instructions Messages, On the television

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.

On the television		Page
Authorisation Error.	≥[DivX] You are trying to play the DivX VOD content that was purchased with a different	24
This unit is not authorised to	registration code. You cannot play the content on this unit.
play this title.
Cannot play.	≥You inserted an incompatible disc.	6, 7
Cannot play on this unit.	≥You tried to play a non-compatible image.	7, 34
	≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.	—
No disc is inserted.	≥The disc may be upside down.	—
Rental Expired.	≥[DivX] The DivX VOD content has zero remaining plays. You cannot play it.	24
$ This operation is not	≥Some operations are unsupported by the unit. For example;
available.	– [BD-V]:During play back, reverse slow-motion or reverse frame-by-frame is not possible.	17
$ This operation is prohibited	≥Depending on the disc, you may not be able to perform search or skip when film previews	17
by this disc.	and warning screens are being played back.
Cannot connect.	≥When a hub is used but its Link lamp does not light up, check the cable connection, LAN	13
Please check the connection of	terminal connection, cable itself (a cross cable may be used by mistake), etc.
the LAN cable.
IP address is not set.	≥The “IP Address” in “IP Address / DNS Settings” is “---. ---. ---. ---“. Set the “IP Address”,	14
	“Subnet Mask”, and “Gateway Address“. (Select the automatic address acquisition if
	necessary.)
Cannot obtain IP address.	≥If you use a hub, then check the connection between the hub and the router.	13
Please check the connection or	– Use the UPLINK port of the hub to connect to a router.
setting of the router.	– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the
	cable connection, LAN terminal connection, cable itself (a cross cable may be used by
	mistake), etc.	13
	≥If the above conditions are OK, then the router may not operate in DHCP mode. Check the
	router settings and operation. You may reset the router to restore it to normal.
This IP address is already in	≥This unit’s IP address is used by another device. Check the IP addresses of this unit,	—
use.	personal computers, and routers, etc. If necessary, reconfigure them to avoid IP
Please check the setting.	addresses from being duplicated.
Connection test could not be	≥Turn the unit off. Remove the AC mains lead and reconnect it and try again. If the same	—
conducted.	symptom persists, then consult your dealer.
IP address is not set correctly.
Connection test was	≥If you use a hub, then check the connection between the hub and the router.	13
unsuccessful. No reply from	– Use the UPLINK port of the hub to connect to a router.
Gateway. Please check the	– If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal
connection or setting of the	connection, cable itself (a cross cable may be used by mistake), etc.	14
router.	≥Check the “IP Address”, “Subnet Mask”, and “Gateway Address” in the “IP Address / DNS
	Settings”.	14
	≥If the MAC address information is required, then press [SETUP] to display the “Network
	Settings” menu.
Network connection was	≥When you set “BD-Live Internet Access” to “Limit” and play BD-Live contents which do not	29
rejected.	have a content owner certificate, the Internet access of the content is not allowed. If you
Please confirm Setup “BD-Live	allow the content to connect to Internet, set “BD-Live Internet Access” to “Permit”.
Internet Access”.
Could not check for latest	≥The firmware download server is currently unavailable. Please try again later.	—
firmware version.
Please try again later.
High Clarity Sound is effective.	≥[BD80] “High Clarity Sound” in setup menu is set to “Enable”, and “High Clarity Sound” in	27, 30
Analog video output is turned	on-screen menu is set to “On”.
off when playback starts.

RQT9401

36