Panasonic DMP-BDT105 operating instructions Picture

Page 33

Picture

The images from this unit do not appear on the television.

Picture is distorted.

¾An incorrect resolution is selected in “Component Video Resolution” or “HDMI Resolution”. Reset the setting as follows:

1 While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than

5 seconds.

– “00 RET” is displayed on the unit’s display.

2Repeatedly press [1] (right) on the remote control or [POWER Í/I] on the unit until “04 PRG” is displayed on

the unit’s display.

3Press and hold [OK] on the remote control or [< OPEN/ CLOSE] on the unit for at least 3 seconds.

Set the item again. (> 30)

–When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream, select “Yes” in “Restore Default Settings” and make proper settings. (> 31)

¾When “Playback Method for 3D Disc” in the Setup menu is set to “3D Playback”, images may not output depending on the connection method. Remove the disc from this unit and select “2D Playback”. (> 28)

Video is not output in high-definition.

¾Confirm that the “HDMI Video Mode”, “HDMI Resolution”, and “Component Video Resolution” in the Setup menu are set properly. (> 30)

3D video is not output.

¾Is there a non-3D compatible amplifier/receiver connected between this unit and a TV? (> 10)

¾Are the settings on this unit and the TV correct? (> 21)

¾Is the amplifier/receiver that is connected between this unit and TV on?

3D video is not output correctly as 2D.

¾Is the “Playback Method for 3D Disc” set to “2D Playback”? (> 28)

¾Discs that have recorded titles with Side by side (2 screen structure) which can be enjoyed in 3D are played back in accordance with the settings of the TV.

No subtitles.

¾When progressive output is on, closed captions/subtitles cannot be displayed.

The subtitles overlap closed captions recorded on discs.

¾Turn off the subtitles or turn off the closed caption setting on the TV. (> 26)

A black band is displayed around the edge of the screen.

The aspect ratio of the screen is abnormal.

¾Confirm the “TV Aspect” is set properly. (> 30)

¾Adjust the aspect setting on the television. (Adjustment using “Screen Aspect” (> 18) on the unit is also possible)

Audio

Cannot switch audio.

¾When connecting an amplifier/receiver using an OPTICAL terminal or an HDMI terminal, you cannot switch the audio if “Digital Audio Output” is set to “Bitstream”. Set “Digital Audio Output” to “PCM” or connect using AUDIO OUT terminal. (> 9, 29)

Cannot hear the desired audio type.

¾Check the connections and the “Digital Audio Output” settings. (> 29)

¾To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to “On” in the Setup menu. (> 30)

Reference

VQT2U33 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents If you have any questions contact Model No. DMP-BDT100Following Applies only in the U.S.A. FCC Note Important Safety InstructionsTable of contents Accessory Using the remote controlUnit and media care Power button Power Í/I Control reference guideFront panel Playable discs/Cards/USB devices Type Logo examples Type detail Playable contentsRegion management information Discs that cannot be played in this UnitFinalize BD-VideoHighest Quality Video Connecting to a TVStandard Quality Video Audio/Video Component CableConnecting to an amplifier/receiver Digital AudioHdmi cable Multi channel speakers Amplifier/receiver ≥ Firmware can be updated Connecting to a broadband networkWireless router Access point, etcSetting Connecting to an AC powerEasy Setting Press Í PowerNetwork Easy Setting When you experience problems with settingsSelect Wired or Wireless and press OK Network Easy Setting Connection Check Network Easy Setting Internet Connection CheckDisplay Reprogramming the remote control Firmware updatesFor other Panasonic products To switch drives Inserting or removing mediaFunctions menu Playing video contents Press SUB Menu Select an item, then press OK Useful functionsPlaying picture-in-picture Enjoying BD-Live discs with InternetDeleting data/Formatting SD cards Regarding DivX Cancel the unit’s registrationDisplaying subtitle text Set Subtitle in DiscEnjoying 3D video 3D settingsPlaying still pictures To show the picture propertiesBD-RE, DVD-RAM Playing a track in another folder Playing musicInsert a disc or USB device Press 3, 4 to select the track and press OKEnjoying Viera Press Viera CastPress 3, 4, 2, 1 to select the item and press OK Automatic input switching Power on link Easy control only with Viera remote controlPower off link Linked operations withDisc Playback menuPlay VideoAudio Setup menu DTS/DTS-HD DisplayTV / Device Connection Network OthersCast Troubleshooting guide General operationCannot eject disc Picture Playback Messages On the televisionOn the unit’s display Audio Information About audio from audio output terminalsHdmi AV OUT/DIGITAL Audio OUT Recommended audio output setting For details of the each item, refer toBitstream Subtitles text file of DivX DivXStructure of folders that can be played in this unit Supplemental information Specifications Fitness for a Particular Purpose Glossary As of November Product or Part Name Parts LaborLimited Warranty Only for Canada Link ServicentresTM locator under Customer supportFor Product Operation ASSISTANCE, please contact Referencia rápida en Conexiones básicasReproducción básica Reference Off Timer On-screen Language Picture-in-picture Playback AC Power Connection Angle AudioIndex Local storage M MPEG2 MP3 Network
Top Page Image Contents