Panasonic DMP-BDT105 operating instructions Messages, On the television, On the unit’s display

Page 35

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.

On the television

Cannot play.

¾You inserted an incompatible disc (Discs recorded in PAL video, etc.).

Cannot display on this unit.

¾You tried to play a non-compatible image.

¾Confirm “SD” on the unit’s display is not blinking and re-insert the card.

No disc is inserted.

¾The disc may be upside down.

$This operation is not available.

¾Some operations are unsupported by the unit. For example;

–BD-Video: During playback, reverse slow-motion or reverse frame-by-frame is not possible.

IP address is not set.

¾The “IP Address” in “IP Address/DNS Settings” is “---.

---. ---. ---”. Set the “IP Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address acquisition if necessary.)

On the unit’s display

F99

¾The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.

HDMI ONLY

¾Some BD-Video discs can only be output with HDMI.

NET

¾Displays while VIERA CAST is starting up.

No PLAY

¾There is a viewing restriction on a BD-Video or DVD-Video. (> 28)

No READ

¾The media is dirty or badly scratched. The unit cannot play.

PLEASE WAIT

¾The unit is carrying out an internal process. This is not a malfunction. You cannot operate the unit while “PLEASE WAIT” is displayed.

REMOVE

¾The USB device is drawing too much power. Remove the USB device.

SET 

(“ ” stands for a number.)

¾The remote control and main unit are using different codes. Change the code on the remote control.

Press and hold [OK] and the indicated number button at the same time for more than 5 seconds.

U59

¾The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.

Select a position with good ventilation when installing the unit. Do not block the ventilation hole on the rear and side of the unit.

U72

U73

¾The HDMI connection acts unusually.

–Turn the unit and TV off.

–Disconnect the HDMI cable between the player and the TV.

Hor F

(“ ” stands for a number.) ¾ There is something unusual.

¾ Check the unit using the troubleshooting guide. If the service number does not disappear, do the following.

1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.

2Press [POWER Í/I] to turn the power on.

If the service number does not disappear despite doing the above, request service from the dealer. Inform the dealer of the service number when requesting service.

START

¾The system is being restarted during the firmware update. Please do not turn off power.

UPD/

(“ ” stands for a number.)

¾The firmware is being updated. Please do not turn off power.

FINISH

¾The firmware update is complete.

Reference

VQT2U33 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents If you have any questions contact Model No. DMP-BDT100Following Applies only in the U.S.A. FCC Note Important Safety InstructionsTable of contents Unit and media care AccessoryUsing the remote control Front panel Power button Power Í/IControl reference guide Playable discs/Cards/USB devices Type Logo examples Type detail Playable contentsBD-Video Discs that cannot be played in this UnitRegion management information FinalizeHighest Quality Video Connecting to a TVStandard Quality Video Audio/Video Component CableHdmi cable Multi channel speakers Amplifier/receiver Connecting to an amplifier/receiverDigital Audio Access point, etc Connecting to a broadband network≥ Firmware can be updated Wireless routerPress Í Power Connecting to an AC powerSetting Easy SettingSelect Wired or Wireless and press OK Network Easy SettingWhen you experience problems with settings Display Network Easy Setting Connection CheckNetwork Easy Setting Internet Connection Check For other Panasonic products Reprogramming the remote controlFirmware updates Functions menu To switch drivesInserting or removing media Playing video contents Press SUB Menu Select an item, then press OK Useful functionsDeleting data/Formatting SD cards Playing picture-in-pictureEnjoying BD-Live discs with Internet Set Subtitle in Disc Cancel the unit’s registrationRegarding DivX Displaying subtitle textEnjoying 3D video 3D settingsBD-RE, DVD-RAM Playing still picturesTo show the picture properties Press 3, 4 to select the track and press OK Playing musicPlaying a track in another folder Insert a disc or USB devicePress 3, 4, 2, 1 to select the item and press OK Enjoying VieraPress Viera Cast Linked operations with Easy control only with Viera remote controlAutomatic input switching Power on link Power off linkDisc Playback menuAudio PlayVideo Setup menu DTS/DTS-HD DisplayTV / Device Connection Cast NetworkOthers Cannot eject disc Troubleshooting guide General operation Picture Playback On the unit’s display MessagesOn the television Hdmi AV OUT/DIGITAL Audio OUT Audio InformationAbout audio from audio output terminals Bitstream Recommended audio output settingFor details of the each item, refer to Subtitles text file of DivX DivXStructure of folders that can be played in this unit Supplemental information Specifications Fitness for a Particular Purpose Glossary As of November Product or Part Name Parts LaborFor Product Operation ASSISTANCE, please contact Limited Warranty Only for CanadaLink ServicentresTM locator under Customer support Reproducción básica Referencia rápida enConexiones básicas Reference Local storage M MPEG2 MP3 Network AC Power Connection Angle AudioOff Timer On-screen Language Picture-in-picture Playback Index
Top Page Image Contents