When you experience problems with settings

When you experience problems with settings

Access Point Connection Setting

Failed to connect to the access point.

A conflict with another device occurred.

Do you want to configure Access Point Connection

Setting again ?

YesNo

Display	Check the following
A conflict with another	≥ Please wait a few moments,
device occurred.	and then try again.

	≥ Setting of the Wireless router
	(Access point) for MAC
A time out error occurred.	Address etc.
	≥ The SSID and the encryption
	key of the Wireless router
	(Access point).
	(Access point).
	≥ Please wait a few moments,
An authentication error or a	and then try again.
time out error occurred.

	≥ Connection of Wireless LAN
	Adaptor
A device error occurred.	If there is no improvement in
	symptom, contact our
	Customer Service Center.

Network Easy Setting (Connection Check)

Complete.
1.	LAN cable connection	: Fail
2.	IP address setting	: Fail
3.	Connection to gateway	: Fail

LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.

Yes	No
OK

	Display			Check the
	Display			following
				following
1. LAN cable connection or			: Fail	≥ Connection and
Connection to access point			: Fail	settings of
Connection to access point				settings of
2. IP address setting			: Fail	Wireless router
2. IP address setting			: Fail	(Access point)
				(Access point)
				≥ Connection of
3. Connection to gateway			: Fail	the LAN cables
				(> 31)

1. LAN cable connection or			: Pass	≥ Connection and
Connection to access point			: Pass	settings of
Connection to access point				settings of
2. IP address setting			: Fail	Wireless router
2. IP address setting			: Fail	(Access point)
				(Access point)
3. Connection to gateway			: Fail	≥ Connection and
				settings of the
1. LAN cable connection or				settings of the
1. LAN cable connection or			: Pass	hub and router
Connection to access point			: Pass	hub and router
Connection to access point				≥ Settings of “IP
				≥ Settings of “IP
2. IP address setting			: Pass	Address/DNS
3. Connection to gateway			: Fail	Settings” (> 39)
3. Connection to gateway			: Fail
					Network
Network Easy Setting (Internet Connection Check)					Network
Network Easy Setting (Internet Connection Check)
Network Easy Setting (Internet Connection Check)

	Complete.
	- Connection to the Internet : Fail(Error code: B019)


	Failed the connection test.
	Cannot find the server.(Error code: B019)
	Please refer to the operating instructions for the cause
	of the error and the solution for it.
	Press [OK].
	OK

	Display		Check the following
Cannot find the server.		≥ “Primary DNS” and “Secondary
(Error code: B019)		DNS” settings of “IP Address/DNS
(Error code: B019)		Settings” (> 39)
		Settings” (> 39)

		≥ The server may be busy or the
Failed to connect to		service may have been
Failed to connect to		suspended. Please wait a few
the server.		suspended. Please wait a few
the server.		moments, and then try again.
(Error code: B020)		moments, and then try again.
(Error code: B020)		≥ Settings of “Proxy Server Settings”
		≥ Settings of “Proxy Server Settings”
		(> 39) and the router

≥Refer to the operating instructions of the hub or router.

≥You can perform this setup anytime by selecting “Network Easy Setting” in the Setup menu. (> 32)

≥You can redo these settings individually using “Network Settings”. (> 39)

≥After performing network settings on this unit, the settings (encryption level, etc.) of the Wireless router (Access point) might change. When you have trouble getting online on your PC, perform the network settings on your PC in accordance with the settings of Wireless router (Access point).

VQT2J81

(ENG)