Arcam BDP100 manual Making video connections, Making audio connections

Page 6

Making video connections

To view the pictures from the BD player you need to connect one of its video outputs to your display device (TV, monitor, projector, etc.) or AV receiver (such as the Arcam AVR600).

The BDP100 has three video output options, described below. You need only use one type of video from the list; choose a type that your display device or AV receiver supports. If your equipment does not support any of the above connection types then you will be unable to use it directly with the BDP100 and a video converter device may be required. In this case, please contact your dealer for further assistance.

AV receivers and other video processing devices may be connected between the BDP100 and your display. Ensure that all the equipment supports the type of video signal you intend to use. For instructions on how to connect AV equipment, consult the manual for that equipment.

HDMI dIgiTal vIDEO

The HDMI connector offers uncompressed digital video and audio transmission between the BDP100 and the display device, and provides the highest quality output. Generally, it is also the easiest connection type to configure.

To use this video connection, you will require a HDMI or HDMI/DVI cable between the BDP100 and your display device or receiver. See page E-7 for further details.

CoMPONENT vIDEO

Use three 75Ω phono cables to connect the Component Y, Pb, Pr outputs of the BD player to the Y, Pb, Pr inputs of the display device. Ensure that the cables are suitable for video use and that they are approximately the same length.

If your television is capable of accepting a progressively scanned (de-interlaced) video signal, you may wish to use the progressive video output from the BDP100. If you are unsure whether your display device can accept progressive video, please refer to its instruction manual or consult your dealer.

Making audio connections

The BDP100 offers a number of alternatives for connecting audio. The connection type to use depends on the rest of your system; chose the type most appropriate to your amplifier.

If you want to listen to audio through...

...we recommend the following:

<Your television

How you listen to audio through your TV depends on the inputs it has and your video connection:

<HDMI: If you are using an HDMI connection (not DVI), this will carry both audio and video. No further connection is required.

<Digital Audio (Coaxial or Optical): If your TV has Digital Audio inputs on Coaxial or Optical connectors, connect the appropriate digital audio lead between the TV input and the appropriate BDP100 digital output. Do not make a connection between the BDP100 and a TV’s Digital Audio output.

<Stereo phono: If your TV has stereo phono inputs, follow the instructions below for a stereo amplifier.

<Your stereo amplifier

If you wish to listen to audio from your player through a stereo amplifier, then use the stereo analogue outputs. These outputs provide a stereo down-mix of the source material.

Using a stereo phono cable of a suitable length, connect the outputs labeled zoNE 1 audIO to the left and right inputs (respectively) for DVD or CD on your amplifier.

<Your surround-sound receiver

Connect the HDMI output to your receiver (for audio and video) if the receiver supports audio over HDMI. The HDMI connection supports all possible audio formats including Dolby TrueHD, DTS Master Audio and multichannel PCM.

If your receiver does not support HDMI audio, connect one of the Digital Audio outputs (Optical or Coaxial) to the ‘Blu-ray’, ‘BD’ or ‘DVD’ input of your receiver. These digital outputs provide PCM, Dolby Digital, DTS or MPEG multi-channel audio, depending on the source material. The BDP100 can also be set to re-encode all audio to DTS (“Bitstream Mixed”) (see “Audio” on page E-21). This option provides the best surround sound quality for Digital Audio connections.

You may also wish to connect the stereo analogue audio outputs to the CD input on your receiver, for listening to CDs. This will allow the BDP100’s audiophile digital-to-analogue circuitry to be utilised, for the best stereo sound quality.

CoMPOSITE vIDEO

If your display device offers only a composite input (sometimes labelled CVBS or just ‘video’), connect this to the COMPOSITE video output of the BD player using a 75Ω phono cable suitable for video use. Note that a composite video connection gives the lowest- quality output; if your display device supports other video connection types, we advise that those are used instead.

E-6

Using two video connections simultaneously

It is possible to use two video connections simultaneously (routing one connection to a second room or display, for example). If you wish to do this, please read these notes:

<The Composite video output is always active. It carries interlaced output at all times.

<The Component video output is always active.

It can be set to carry either interlaced or progressive-scan output.

<The HDMI output is active only if a compatible display is detected by the BDP100. It can be set to carry either interlaced, progressive-scan or high-definition output.

Image 6 Arcam BDP100 manual Making video connections, Making audio connections, Using two video connections simultaneously
Contents BDP100 HAn d b o o k Blu-ray Disc playerSafety Guidelines Important safety instructionsSafety compliance Contents WelcomeEnglish Remote control and trigger inputs InstallationPower Placing the unit12V trigger input Power inletAnalogue audio output Coaxial digital outputUsing two video connections simultaneously Making video connectionsMaking audio connections Hdmi interface Connecting using HdmiTroubleshooting Hdmi About HdmiPlayable files Disc & file FormatsPlayable discs Region codingNetwork connection USB connectionTo skip chapters or tracks on a CD, press / or Basic OperationIntroduction On the front panel or 4 on the handsetUsing the remote control BDP100 is supplied with the CR104 universal remote controlControlling the BDP100 Select the source key firstPause playback. Press 4 to resume playback Advanced controlsFast rewind Starts playback Displays Search menu with Time, Title Track optionsDevice Mode / Source keys Useful informationControlling other devices Code blink-backSubtitles Disc Information MenusSoundtrack Selection SearchBonusview & BD-Live Virtual PackageBD-Live Play menu Play Mode menuPlaying files Media menuAdvanced playback controls Navigating the menus Settings MenusEntering the settings menu Unstable OSD menu or picture display?Audio Output resolution must be set to 1080p or Hdmi AutoDisplay LanguageNetwork Wired NetworkSystem Network TestPower switch again and then unload the disc TV does not support HdcpAudio Audio output formatEnglish Video Output Resolution 480i 576iCustomising CR104 Code LearningVolume punch-through Creating MacrosKey Mover To restore a moved Device Mode key to its original state Mode MoverLocking/Unlocking a specific Device Mode Copy a key between Device ModesMode key IR punch-through Resetting the CR104Commands DecimalLaser radiation SpecificationsRadio interference Continual improvement policySoftware licencing English Page Correct disposal of this product Product GuaranteeWarranty covers This marking indicates that this
Related manuals
Manual 148 pages 8.14 Kb