Hitachi CP-S833W, CP-S833E Lamp, Message table, On-screen display, Reset the lamp time, Action

Page 30

Lamp (continued)

5

Install the lamp cover and fix it using screws.

∙ To prevent burn, install the lamp cover and secure it using the screws.

∙ Do not turn on the power with lamp cover removed.

Whenever the lamp is replaced, reset the total operation time of the lamp.

Do not reset if the lamp has not been replaced.

2. Reset the lamp time

Please carry out the following operation within 10 minutes from power on, if you replaced the lamp after

2,000 hours.

3

2

MAGNIFY VOLUME

OFF

POSITION ON

LASER

3

RESET

RIGHT

1

MENU ON

MOUSE ON

BLANK TIMER

RGBVIDEO

INPUT

RESET

1, 2

 

MENU

MUTEINPUT

ON

LAMP TEMP

STANDBY/ON

1)Press the RESET button on projector for 3 seconds or remote control TIMER button for 3 seconds and display the total lamp used time.

When accumulated operation time of the lamp reaches 1700 hours, the following display will appear at the bottom of the screen.

2)Press the RESET button on projector or remote control MENU ON button during displaying the lamp used time.

3)Select the “0” on the screen using the MENU ( ) button or DISK PAD.

LAMP 1700 h

LAMP 1700 □→ 0 CANCEL

Message table

On-screen display

The following messages are displayed on the screen.

 

MESSAGE

Action

 

 

 

 

CHANGE THE LAMP

Accumulated operation of lamp has exceeded 1,700 hours. It is recommended

 

"AFTER REPLACING LAMP,

to replace lamp. Replace with new lamp. If accumulated operation reaches

 

RESET THE LAMP TIMER."

2,000 hours, lamp will automatically turn off. *1

 

CHANGE THE LAMP

Lamp has 1,979 hours on it.

 

"AFTER REPLACING LAMP,

Call a maintenance person. *1

 

RESET THE LAMP TIMER."

Time is 20 ~ 0. (count down.)

 

THE POWER WILL TURN

 

 

OFF AFTER 20 Hr.

 

 

 

 

 

Bilnking of

When the lamp has 2,000 hours or more on it, the message will blink, and the

 

"CHANGE THE LAMP"

power will turns off after 10 minutes.

 

 

 

 

NO INPUT IS DETECTED

Signal is hot input. (See page 19, 20)

 

 

 

 

SYNC IS OUT OF RANGE

The horizontal frequency of the input signal exceeds the range of the projector,

 

it cannot be displayed. (See page 20, 21)

 

 

 

 

 

 

CHECK THE AIR FLOW

Clean the air filter of remove the blocking ventilation holes. (See page 28)

 

 

 

30

*1 This message are not displayed after 3 minutes.

But this message are displayed when you turn on the power again.

Image 30
Contents Outline FeaturesContents Operating GuideFor the Customers in U.K Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursHandle the power cord carefully Be careful in handling the power cordCleaning Do not step on this unit or do not put a Heavy object on itDo not place this unit where it gets hot When you are not going to use For a long timeClean inside the unit at least once two years VolumeNames and functions of each part Main unitRGB output terminal AC in socket Main Power switchRemote control sensor RGB input terminal Video input terminalRemote control transmitter How to insert batteries Replace the coverHow to use foot adjusters InstallationExample of the projector and screen installation View from the topBasic operations To project the pictureTo turn off the power PLUG&PLAYFreeze Function Magnifying FunctionAdjustments and functions To return to the initial settingMemory function SET UP Adjustment Item Details of adjustmentInput ImageOPT Connection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeInitial set signals Computer/signal Horizontal Timing µsComputer/signal Vertical Timing lines Serial Control signal terminalPin No RS-232C Mouse PS/2 +5VPS/2 mouse ADB Mac mouseSerial mouse Control command table Control command tableCommunication Control data table Procedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorAC Inlet Example of system setupConnecting various equipment VTR, etc Video model onlyCleaning the air filter Install the air filterHow to replace lamp Remove the lamp coverLoosen two screws and pull Handle to remove Lamp.Screw Message table Reset the lamp timeLamp On-screen displayWhen you think something wrong RCA Jack terminal Terminal Dimension diagramRCA Jack terminal Input terminal Input/Output Operating guide RGB cable

CP-S833W, CP-S833E specifications

The Hitachi CP-S833E and CP-S833W projectors stand out in the market for their balance of quality, performance, and versatility, making them ideal for both business presentations and educational environments. These projectors are designed to provide vibrant visuals, ensuring that audiences remain engaged and informed.

One of the main features of the CP-S833E and CP-S833W is their high brightness level, rated at around 3,000 ANSI lumens. This impressive brightness ensures that images are clear and visible even in well-lit rooms. Coupled with a high contrast ratio, these projectors deliver sharp images with deep blacks and vibrant colors, enhancing the overall viewing experience.

Both models utilize 3LCD technology, which helps in producing accurate color reproduction while minimizing the risks of color breakdown often associated with other projection technologies. The 3LCD system effectively uses three chips to project red, green, and blue light, resulting in richer and more natural images.

The Hitachi CP-S833E and CP-S833W are equipped with a native XGA resolution of 1024 x 768 pixels. This resolution strikes a good balance between image quality and performance, making it suitable for various content types, whether it be text-heavy slides, videos, or images. Furthermore, the projectors support various input options, including HDMI, VGA, and composite video, allowing for easy connectivity with a wide range of devices.

Additionally, these projectors come with features such as keystone correction and a built-in speaker, which enhance flexibility and functionality. Keystone correction allows users to adjust the projected image, ensuring it maintains a proper rectangular shape even when the projector is not perfectly aligned with the screen. The built-in speaker makes it convenient for users to present without needing additional audio equipment.

In terms of energy efficiency, both models are designed to consume less power. They feature a long lamp life, extending up to 5,000 hours in eco mode, which reduces replacement costs and contributes to lower overall operating expenses.

Overall, the Hitachi CP-S833E and CP-S833W projectors combine advanced technology with user-friendly features, making them a reliable choice for any presentation setting. Their impressive brightness, color accuracy, and versatile connectivity options ensure that they can meet the diverse needs of users, whether in classrooms or boardrooms.