Picture-In-Picture Pip, PIP button | Hitachi 65SWX20B, 57SWX20B

PICTURE-IN-PICTURE (PIP)

Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B).

ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture. To select between main picture and PIP sub-picture tuning, press the PIP CH button on the remote. The green highlighted channel display will move with every press of the PIP CH button. When the top channel display is highlighted, channel tuning is for the main picture. When the lower channel display is highlighted, channel tuning is for the PIP sub-picture.

The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from the ANT A source or any of the video inputs.

ANT A
			DVI-HDTV
		PR	PB	Y
	INPUT 1
TO		R	(MONO)/L
CONVERTER				AUDIO
		PR	PB	Y/VIDEO
ANT B	INPUT 2	R	(MONO)/L
		R	(MONO)/L
				AUDIO
		R	(MONO)/L	VIDEO	S-VIDEO
	INPUT 3
AUDIO
TO HI-FI
CENTER		R	(MONO)/L	VIDEO	S-VIDEO
IN	INPUT 4
IR
BLASTER		R	L	VIDEO	S-VIDEO
L	MONITOR
L	OUT
	OUT
			AUDIO
R
			Audio	Video
			OUTPUT
			VCR

	MEN		EXIT
		U
VOL		SELECT			CH
VOL					CH
SV	M	UTE	LAST	CH
CS			LAST		SCHD
VCR	PLUS+				SCHD
VCR
V			GUIDE/TV		VID	5
ID1					VID
VID 2			VID 3	VID	4
			VID 3
PIP		PIP CH			FREEZE	,
						,
			PIP ACCESS
PIP MODE			SWAP		VIDEO
PIP MODE					VIDEO

REC

CLU-5722TSI

Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, V:1, V:2, V:3, V:4, or V:5). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT A, V:1, V:2, V:3, V:4, or V:5).

PIP button

Press the PIP button and a sub-picture will appear in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the last selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the four different modes.

POP MODE PICTURE-IN-PICTURE

Press the PIP button and a sub-picture appears in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the last selection of the PIP mode. Press the PIP button again to remove the sub-picture from the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by green highlighted channel display.) Press the VID1, VID2, VID3, VID4 or VID5 button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3, VIDEO:4 and VIDEO:5 and ANT:A source. (ANT B source cannot be viewed as a sub-picture.)

PIP

Ant A 10	Main Picture
	PIP
	Sub Picture

Ant A 10

NOTES: 1.	When ANT B is selected as the main channel, the SWAP feature is disabled.
2.	In POP mode, thumb stick CURSOR , will move the sub-picture up/down.

PIP MODE PICTURE-IN-PICTURE(This feature is only available in 1080i input signal)

To prevent a pattern burn, occasionally move the sub-picture using the THUMBSTICK.

PIP

Ant A 10