Hitachi 43GX10B, 50DX10B, 50GX30B, 60DX10B Rear Speaker Terminal Connections

Page 12

REAR SPEAKER TERMINAL CONNECTIONS

CONNECT AFTER TURNING THE POWER OF THE TV OFF.

Press the Right Speaker red button and insert the positive (+) lead wire into the hole next to the button. Once the wire is in place, pull the red button back to original position and the wire is locked into place. In the same manner, press the Right Speaker black button and insert the negative (-) lead wire. Repeat this procedure for the Left Speaker.

CAUTION: Do not short speaker terminal, (do not connect a wire directly across any two terminals). This could cause damage to your audio outputs or other damage to your TV.

REAR SPEAKER

TO

 

EXTERNAL

L

SPEAKER

 

 

R

CAUTION: Do not connect speakers simultaneously to the REAR SPEAKER terminal of the Projection TV and an external amplifier. This could damage both the TV and the speakers. Your TV was designed to use 8-Ohm speakers only. Any other type may degrade the audio performance of your entertainment system.

Projection T.V.

Speaker

Amplifier

TIPS ON REAR PANEL CONNECTIONS

S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connec- tions in place of the standard video connection if your device has this feature.

If your device has only one audio output (mono sound), connect it to the left audio jack on the television.

Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.

A single VCR can be used for VCR#1 and VCR#2, but note that a VCR cannot record its own video or line output. (INPUT 1 in example on page 11). Refer to your VCR operating guide for more information on line input-output connection.

You may use VIDEO or S-VIDEO inputs to connect to INPUT 1 and 2, but note that only one of these may be used at a time.

Connect only 1 component to each input jack.

COMPONENT VIDEO: Y-PBPRconnections are provided for high performance components, such as DVD players. Use these con- nections in place of the standard video connection if your device has this feature.

Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV s PB input and the components R-Y output to the TV s PR input.

Your component outputs may be labeled Y-CBCR. In this case, connect the components CB output to the TV s PB input and the components CR output to the TV s PR input.

It may be necessary to adjust TINT or turn AUTO COLOR-ON to obtain optimum picture quality when using the Y-PBPRinputs. (see pages 47 and 48)

To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPRjacks.

12

Image 12
Contents 43GX10B 50DX10B 50GX30B 60DX10B Important Safety Instructions Refer Servicing to Qualified Service PersonnelImportant Safety Instructions Safety Tips Operation of Your TelevisionAccessories Remote ControlPart Name Illustration HOW to SET UP Your NEW Hitachi Projection TV AntennaLocation ViewingHOOK-UP Cables and Connectors Antenna Connections to Rear Jack PanelFront Panel Controls Power light Remote Control sensorPerfect Picture sensor Digital ArrayRear Panel Jacks Way signal splitter Rear Panel ConnectionsConnect After Turning the Power of the TV OFF Rear Speaker Terminal ConnectionsConnecting External Audio Amplifier External ConnectionsConnecting External Video Sources Connecting a Monaural Audio VCR or Laserdisc PlayerBefore Operating External Video Source Connecting a Stereo VCR or Stereo Laserdisc Player Optional, see tips onConnecting a Stereo Laserdisc Player or DVD Player to Input Audio System Setup Surround Required Optional Effect Feature Switch ConnectionRemote Control Precoded VCR/DVD ButtonsPrecoded VCR/DVD codes TV/VCR ButtonHOW to USE the Remote to Control Your TV PICTURE-IN-PICTUREMENU, SELECT, Cursor buttons Last Channel buttonStereo ST/SA TakaVIDEO1 VID1 VIDEO2 VID2PIP CH buton Help buttonPICTURE-IN-PICTURE PIP PIP buttonSwap button Move buttonCursor buttons PICTURE-IN-PICUTRE PIP Freeze buttonQuick Freeze button Using the Remote to Control VCR Functions Operating the precoded function for your VCRUsing the Remote to Control DVD Functions Operating the precoded function for your DVD PlayerUsing the Remote to Control Cable BOX/SATELLITE Functions Operating the precoded function for your cable/satellite boxCABLE, SATELLITE, VCR, and DVD Codes Ultratec OSD Theater SET UP Menu LanguageSignal Source Reception BandAuto Channel SET Channel Memory Cursor Channel ListR S O R Clock SETRed Custom Channel IDVideo ID Family Favorites Menu Family Favorites Operation Parental Control Customize Use number buttons to enterEvent Prog Auto Link Closed Caption DisplayMode ChannelReset VideoContrast Brightness Color Tint SharpnessAdvanced Settings Color TemperaturePerfect Picture Auto ColorAudio BassTreble BalanceMTS Mode Auto Noise CancelPerfect Volume Internal SpeakersTheater Theater ModesCare of Your Hitachi Projection TV Your Remote Control Do notReception Problems ¥ Ignition NoiseSymptoms Useful InfoSpecification InputsOutputs 43GX10B 50DX10B 60DX10B 50GX30BHitachi Home Electronics DivisionPage Page Page QR47632