Hitachi 43GX10B, 50DX10B, 50GX30B, 60DX10B important safety instructions Red

Page 38

SETUP

SET UP

DIGITAL ARRAY

Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the proper proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be precisely aligned over each other so that the colors can be mixed. The process of aligning these picture beams is called convergence .

Over a period of time, the picture tubes can drift out of alignment due to normal bumps and vibrations or moving the TV. If you move your TV, or if, after a time, you notice color rings or halos around objects in the picture, you may want to converge (align) the colors.

Properly converged, the lines appear white, which is actually a combination of the outputs of the three color tubes. The output of the green tube is stationary. The outputs of the red and blue tubes can be adjusted. When properly aligned, the outputs of all three tubes should be directly over each other to produce the white lines.

To simplify convergence, HITACHI incorporates a feature to allow you to display a test pattern of horizontal and vertical lines at 9 different locations on the screen. Simply use the remote control to adjust the red and blue colors to match the green. When properly aligned, the outputs of all three tubes should be directly over each other to produce the white lines.

To enter this adjustment mode, you may also select DIGITAL ARRAY from the Set Up menu. However, this will display a message prompting you to press the front panel DIGITAL ARRAY button.

DIGITAL

ARRAY

Red

CURSOR

CURSOR

Blue

MENU

Blue

1

~

9

1

~

9

Blue

DIGITAL

ARRAY

Use the number buttons to select which point to adjust: 1 - Upper Left, 2 - Upper Middle, 3 - Upper Right, 4 - Center Left,

5- Center, 6 - Center Right, 7 - Bottom Left, 8 - Bottom Middle, 9 - Bottom Right. Press the CURSOR buttons to move the displayed color up, down, left, or right.

Press MENU to change the color you want to adjust.

Press the front panel DIGITAL ARRAY button or the remote control MOVE button when adjustment is done. This will save your adjust- ment into memory.

NOTE: Only a momentary press of the DIGITAL ARRAY button is necessary to enter DIGITAL ARRAY convergence adjustment mode.

Do not press the DIGITAL ARRAY button for more than three seconds. This is only for extreme cases of misconvergence and requires assistance from service.

Four lines surrounding a crosshatch indicate the point being adjusted. The color of these surrounding lines indicates the color being adjusted.

To save your adjustment data into memory, press the front panel DIGITAL ARRAY button or the remote control MOVE Button. If you do NOT wish to save your adjustment data into memory, turn the TV OFF or press the remote control PIP button. When the TV is turned ON again, your old convergence data will be restored.

When adjusting convergence, always start at the center of the screen.

38

Image 38
Contents 43GX10B 50DX10B 50GX30B 60DX10B Important Safety Instructions Refer Servicing to Qualified Service PersonnelImportant Safety Instructions Safety Tips Operation of Your TelevisionPart Name Illustration AccessoriesRemote Control Location HOW to SET UP Your NEW Hitachi Projection TVAntenna ViewingHOOK-UP Cables and Connectors Antenna Connections to Rear Jack PanelFront Panel Controls Perfect Picture sensor Power lightRemote Control sensor Digital ArrayRear Panel Jacks Way signal splitter Rear Panel ConnectionsConnect After Turning the Power of the TV OFF Rear Speaker Terminal ConnectionsConnecting External Audio Amplifier External ConnectionsBefore Operating External Video Source Connecting External Video SourcesConnecting a Monaural Audio VCR or Laserdisc Player Connecting a Stereo VCR or Stereo Laserdisc Player Optional, see tips onConnecting a Stereo Laserdisc Player or DVD Player to Input Audio System Setup Surround Required Optional Effect Feature Switch ConnectionPrecoded VCR/DVD codes Remote ControlPrecoded VCR/DVD Buttons TV/VCR ButtonHOW to USE the Remote to Control Your TV PICTURE-IN-PICTUREMENU, SELECT, Cursor buttons Last Channel buttonVIDEO1 VID1 StereoST/SA Taka VIDEO2 VID2PIP CH buton Help buttonPICTURE-IN-PICTURE PIP PIP buttonCursor buttons Swap buttonMove button Quick Freeze button PICTURE-IN-PICUTRE PIPFreeze button Using the Remote to Control VCR Functions Operating the precoded function for your VCRUsing the Remote to Control DVD Functions Operating the precoded function for your DVD PlayerUsing the Remote to Control Cable BOX/SATELLITE Functions Operating the precoded function for your cable/satellite boxCABLE, SATELLITE, VCR, and DVD Codes Ultratec OSD Theater SET UP Menu LanguageSignal Source Reception BandAuto Channel SET Channel Memory Cursor Channel ListR S O R Clock SETRed Custom Channel IDVideo ID Family Favorites Menu Family Favorites Operation Parental Control Customize Use number buttons to enterEvent Prog Auto Link Mode Closed CaptionDisplay ChannelContrast Brightness Color Tint ResetVideo SharpnessPerfect Picture Advanced SettingsColor Temperature Auto ColorTreble AudioBass BalancePerfect Volume MTS ModeAuto Noise Cancel Internal SpeakersTheater Theater ModesCare of Your Hitachi Projection TV Your Remote Control Do notReception Problems ¥ Ignition NoiseSymptoms Useful InfoOutputs SpecificationInputs 43GX10B 50DX10B 60DX10B 50GX30BHitachi Home Electronics DivisionPage Page Page QR47632