Mitsubishi Electronics WS-65611, WS-B55 Connecting a DVD Player, DVD Player with Component Video

Page 21

WARNING: Do not display the same stationary images on the screen for more that 15% of your total TV viewing in one week. Examples of stationary images are letterbox top/bottom bars from DVD or other video sources, side bars when showing standard TV pictures on widescreen TV’s, stock market reports, video game patterns, station logos, black or bright Closed caption backgrounds web sites, or stationary computer images. Such patterns can unevenly age the picture tubes causing permanent damage to the TV.

Connecting a DVD Player

IMPORTANT

•See Appendix B for component video signal compatibility information.

•For digital audio connections, see your A/V Receiver, DVD , and Satellite Receiver Owner’s Guides.

Connecting an S-Video Satellite Receiver

Figure 2. Connecting an S-Video Device.

DVD Player with Component Video

(Figure 1)

1.Connect the Component Video cables from Y/ Cr/Cb or Y/Pr/Pb VIDEO OUT on the back of the DVD player to COMPONENT-1 on the TV back panel, matching the correct connection:

•Y to Y

•Cr or Pr to Pr

•Cb or Pb to Pb

2.Connect a set of audio cables from AUDIO OUT on the back of the DVD player to COMPONENT-1 AUDIO Input on the TV back panel. The red cable connects to the R (right) channel, and the white cable connects to the L (left) channel.

Important: If you add a second DVD or use any other inputs for your DVD, see the section on Editing NetCommand™ Setup to ensure this change is matched by the NetCommand™ system.

S-Video Satellite Receiver

(Figure 2)

1.Connect an S-Video cable from VIDEO OUT on the satellite receiver back panel to VIDEO INPUT-2 on the TV back panel.

2.Connect a set of audio cables from AUDIO OUT on the satellite receiver back panel to the AUDIO INPUT-2, on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

Note: Refer to the Satellite Receiver Owner’s Guide for Dish Antenna connections.

Important: If you add a second Satellite Receiver or use any other inputs for your Satellite Receiver, see the section on Editing NetCommand™ Setup to ensure this change is matched by the NetCommand™ system.

21

Image 21

Contents Owner’s Guide Risk of Electric Shock This Owner’s Guide Important SafeguardsAccessories CleaningPower Source Power-Cord ProtectionDamage Requiring Service Power LinesReplacement Parts Safety CheckConsumer Relations This Section Our Thanks Unpacking Your New TV Special FeaturesPage Chapter TWO Power/Timer System ResetReset Front Control PanelBack Panel IEEE-1394 Input/Output Antenna DTV ANT-DTVDigital Audio Output IR Emitter-Home Theater Control OutputReceiver Input by Manufacturer Connecting External Devices & NetCommand SetupNetCommand Compatible Legacy Devices NetCommand Supported DevicesSeparate UHF and VHF Antennas Antenna or Wall Outlet Cable for Digital BroadcastsCable Box Antenna or Wall Outlet Cable for Analog BroadcastsFor antennas with twin flat lead For cable or antenna with coaxial leadVCR to Analog Antennas or Wall Outlet Cable Figure Connecting an Analog VCRVCR to Cable Box Figure Adding Composite Video or an S-Video with Audio ConnectionsConnecting an A/V Receiver Connecting an Audio/Video Surround Sound ReceiverConnecting a DVD Player DVD Player with Component VideoVideo Satellite Receiver DTV Connectors and Adaptors Connecting an External Digital TV DTV or Hdtv ReceiverExternal DTV Receiver with Component Video Connections DTV Receiver/TV Back panelConnecting an External Digital TV TV or HTV Receiver, External DTV Receiver with RGB Video ConnectionsDTV Receiver / TV Back Panel Connecting the IR-Home Theater Control and IR Repeater Connecting a Computer with a VGA Monitor OutputConnecting a Computer Steps 2-4 Apply both 1A and 1BImportant Notes Cancel Button Radio Buttons NetCommand Setup Getting StartedButtons Back ButtonTV Control and NetCommand Programming the Remote Control to Control NetCommand935 DevicesNetCommand Setup Language ScreenInformation Screen Receiver Screen NetCommand Setup, cont’dCable Box Screen VCR ScreenDBS Screen Camcorder ScreenDVD Screen Finish Screen Review ScreenEdit NetCommand Screen Edit NetCommandAdd ChangeDelete Edit NetCommand, cont’dReview InitialName Screen RF Connection for Cable ScreenFixed Channel Screen Connection for Device Screen Monitor Out to AVR ScreenMonitor Out to VCR Screen AVR to VCR Connection Screen Input-DTV Connection ScreenIR Code for Device Screen Chapter Three Characters or move one space backward 3D Graphical Menu SystemDevice Selection Menu Power On/Off DevicesAudio Section Device Section Video SectionPIP Device Selection Menu PIP/POP Selection MenuMenu Screens Overview Setup MenuAntenna Menu Clock MenuCaptions Menu Timer MenuChip Lock Menu Audio/Video MenuSetup Menu Edit NetCommand Icon Position Edit NetCommand ButtonIcon Position Menu Setup Menu Convergence Reset Factory Defaults MenuConvergence Menu Advanced Convergence Menu Language MenuTransport Menu Channel MemoryName For ANT-A or ANT-BUsing The Remote Control Antenna Menu SuperQuickView SQVSQV SuperQuickView Clock Setting Auto Clock Menu Auto or Manual Clock SettingClock Setting Manual Daylight Savings TimeCaptions Menu Analog and Digital Captions Captions Menu Digital Captions Settings Entry Chip Lock Menu PasscodePasscode Screen ChipChip Lock Menu V-Chip Definitions Chip Signal InformationLock By Time Chip Menu Lock By Time and Front Button LockLock by Time, Lock Time, and Unlock Time Front Button LockTimer On/Off Timer Menu Setting The TimerSet Time DeviceAudio/Video Settings Memory ResetUsing the Audio and Video Buttons on the Remote Control Video MuteTV Speakers Settings Menu TV SpeakersAudio Settings Setting Descriptions AudioVideo Settings Setting Descriptions VideoChapter Four Overview Remote Control Functions OverviewInstalling the Batteries Remote Control Functions Care and OperationFor Best Results from the Remote Control OperationRemote Control Functions Operation of PIP and POP Remote Control Functions Channel Selection and Sleep TimerChannel Selection Sleep Timer Activating the PIP and POPChanging PIP/POP Device Automatic POP SwitchingChanging PIP/Side-by-Side Channels Exchanging Program ImagesDefinitions Remote Control FunctionsPage To Program the Remote to Control NetCommand A/V Products Programming the remote to control your satellite receiver DVD Remote Control Functions Special Functions Video game patterns and scoreboards Bypassing the V-Chip Lock Appendix a Bypassing the V-Chip LockBypassing Front Button Lock Appendix a Bypassing the V-Chip LockPage NetCommand Ieee 1394 & HAVi System Compatibility Input Levels and Timing When Used With RGB Video SignalsComponent-1 and Component-2 Inputs VGA InputReceivers Appendix C Remote Control Programming CodesDVD Players Satellite ReceiversCleaning Appendix D Cleaning and ServiceFor further assistance, call 800 Appendix D Cleaning and Service Appendix E Diamond Shield Instructions Installation Appendix F Cabinet Cabinet Separation for Model WS-65511Appendix F Cabinet Separation Following operation should be performed by two people Cabinet Separation for Model WS-65712Troubleshooting Problem Possible SolutionAppendix Appendix G Troubleshooting DisplayInformation ScreenOn HAppendix On Screen Information DisplaysAnalog Antenna or Devices Digital AntennaPage Index S-W Demo ModeMitsubishi Projection Television Limited Warranty Mitsubishi Projection TV Limited WarrantyMitsubishi TV Software Page Page Connection Helpful Hints Mitsubishi Digital Electronics America, Inc 871D357B10