Mitsubishi Electronics WS-65611, WS-B55, ws-65712, WS-65511 Appendix D Cleaning and Service

Page 75

Cleaning

Normally, light dusting with a dry, non- scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines:

First, turn off the TV and unplug the power cord from the power outlet.

Top and Sides of the TV:

Gently wipe down your TV with a soft, non- abrasive cloth such as cotton flannel or a clean cloth diaper, lightly moistened with water. Dry with a second dry, soft, non-abrasive cloth.

For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent to the water used to moisten the cloth. Rinse with a second cloth moistened only with water. Dry with a third dry, soft, non-abrasive cloth.

Screen behind the Diamond Shield™:

Follow the instructions for the top and sides, however, wipe gently in an up and down motion, following the grooves in the screen.

Clean the entire screen evenly, not just sections of the screen.

Do not allow liquid to drip down the grooves of the screen as some liquid may enter the TV between the screen and the screen frame.

You may purchase Mitsubishi Screen Cleaner, part number CLEANER-VSS, by calling (800) 553-7278.

IMPORTANT

DO NOT use any kind of abrasive or liquid cleaner on the surface of the TV screen or Diamond Shield™.

Anti-Glare Diamond Shield™:

(Diamond Series Models WS-55711, WS-65711, WS-65712 and WS-73711)

Anything abrasive can scratch the anti- glare coating of the Diamond Shield™ and household and window cleaners can remove the coating.

Follow the instructions for cleaning top and sides, however, moisten the cloth with only water.

Do not use any cleaning chemicals on the Diamond Shield™.

DO NOT use Mitsubishi Screen Cleaner on the Anti-Glare Diamond Shield™

Cloth speaker grills:

Lightly brush with a soft brush cloth, or lint brush.

If necessary, you can vacuum using the brush and hose attachments of your vacuum cleaner. Do not use the beater brush section on the grill cloth.

General Cleaning Warnings:

DO NOT allow liquid to enter the TV through the ventilation slots or any crevice.

DO NOT use any strong or abrasive cleaners as these can scratch the surfaces.

DO NOT use any cleaners with ammonia, bleach, alcohol, benzine, or thinners as these can dull the surfaces.

DO NOT spray liquids or cleaners directly on the TV’s surfaces.

DO NOT scrub or rub the TV harshly. Wipe it gently.

IMPORTANT

For further assistance, call (800) 332-2119.

Appendix D: Cleaning and Service

75

Image 75
Contents Owner’s Guide Risk of Electric Shock This Owner’s Guide Important SafeguardsPower-Cord Protection CleaningAccessories Power SourceSafety Check Power LinesDamage Requiring Service Replacement PartsConsumer Relations This Section Our Thanks Unpacking Your New TV Special FeaturesPage Chapter TWO Front Control Panel System ResetPower/Timer ResetBack Panel IR Emitter-Home Theater Control Output Antenna DTV ANT-DTVIEEE-1394 Input/Output Digital Audio OutputReceiver Input by Manufacturer Connecting External Devices & NetCommand SetupNetCommand Compatible Legacy Devices NetCommand Supported DevicesSeparate UHF and VHF Antennas Antenna or Wall Outlet Cable for Digital BroadcastsFor cable or antenna with coaxial lead Antenna or Wall Outlet Cable for Analog BroadcastsCable Box For antennas with twin flat leadAdding Composite Video or an S-Video with Audio Connections Connecting an Analog VCRVCR to Analog Antennas or Wall Outlet Cable Figure VCR to Cable Box FigureConnecting an A/V Receiver Connecting an Audio/Video Surround Sound ReceiverConnecting a DVD Player DVD Player with Component VideoVideo Satellite Receiver DTV Receiver/TV Back panel Connecting an External Digital TV DTV or Hdtv ReceiverDTV Connectors and Adaptors External DTV Receiver with Component Video ConnectionsConnecting an External Digital TV TV or HTV Receiver, External DTV Receiver with RGB Video ConnectionsDTV Receiver / TV Back Panel Steps 2-4 Apply both 1A and 1B Connecting a Computer with a VGA Monitor OutputConnecting the IR-Home Theater Control and IR Repeater Connecting a ComputerImportant Notes Back Button NetCommand Setup Getting StartedCancel Button Radio Buttons ButtonsDevices Programming the Remote Control to Control NetCommandTV Control and NetCommand 935NetCommand Setup Language ScreenInformation Screen VCR Screen NetCommand Setup, cont’dReceiver Screen Cable Box ScreenDBS Screen Camcorder ScreenDVD Screen Finish Screen Review ScreenChange Edit NetCommandEdit NetCommand Screen AddInitial Edit NetCommand, cont’dDelete ReviewName Screen RF Connection for Cable ScreenFixed Channel Screen Connection for Device Screen Monitor Out to AVR ScreenMonitor Out to VCR Screen AVR to VCR Connection Screen Input-DTV Connection ScreenIR Code for Device Screen Chapter Three Characters or move one space backward 3D Graphical Menu SystemVideo Section Power On/Off DevicesDevice Selection Menu Audio Section Device SectionPIP Device Selection Menu PIP/POP Selection MenuClock Menu Setup MenuMenu Screens Overview Antenna MenuAudio/Video Menu Timer MenuCaptions Menu Chip Lock MenuSetup Menu Edit NetCommand Icon Position Edit NetCommand ButtonIcon Position Menu Setup Menu Convergence Reset Factory Defaults MenuConvergence Menu Advanced Convergence Menu Language MenuTransport Menu For ANT-A or ANT-B MemoryChannel NameUsing The Remote Control Antenna Menu SuperQuickView SQVSQV SuperQuickView Daylight Savings Time Clock Menu Auto or Manual Clock SettingClock Setting Auto Clock Setting ManualCaptions Menu Analog and Digital Captions Captions Menu Digital Captions Settings Chip Chip Lock Menu PasscodeEntry Passcode ScreenChip Lock Menu V-Chip Definitions Chip Signal InformationFront Button Lock Chip Menu Lock By Time and Front Button LockLock By Time Lock by Time, Lock Time, and Unlock TimeDevice Timer Menu Setting The TimerTimer On/Off Set TimeVideo Mute Memory ResetAudio/Video Settings Using the Audio and Video Buttons on the Remote ControlTV Speakers Settings Menu TV SpeakersAudio Settings Setting Descriptions AudioVideo Settings Setting Descriptions VideoChapter Four Overview Remote Control Functions OverviewOperation Remote Control Functions Care and OperationInstalling the Batteries For Best Results from the Remote ControlActivating the PIP and POP Remote Control Functions Channel Selection and Sleep TimerRemote Control Functions Operation of PIP and POP Channel Selection Sleep TimerExchanging Program Images Automatic POP SwitchingChanging PIP/POP Device Changing PIP/Side-by-Side ChannelsDefinitions Remote Control FunctionsPage To Program the Remote to Control NetCommand A/V Products Programming the remote to control your satellite receiver DVD Remote Control Functions Special Functions Video game patterns and scoreboards Appendix a Bypassing the V-Chip Lock Appendix a Bypassing the V-Chip LockBypassing the V-Chip Lock Bypassing Front Button LockPage VGA Input Input Levels and Timing When Used With RGB Video SignalsNetCommand Ieee 1394 & HAVi System Compatibility Component-1 and Component-2 InputsSatellite Receivers Appendix C Remote Control Programming CodesReceivers DVD PlayersCleaning Appendix D Cleaning and ServiceFor further assistance, call 800 Appendix D Cleaning and Service Appendix E Diamond Shield Instructions Installation Appendix F Cabinet Cabinet Separation for Model WS-65511Appendix F Cabinet Separation Following operation should be performed by two people Cabinet Separation for Model WS-65712Troubleshooting Problem Possible SolutionAppendix Appendix G Troubleshooting Digital Antenna On Screen Information DisplaysDisplayInformation ScreenOn HAppendix Analog Antenna or DevicesPage Index S-W Demo ModeMitsubishi Projection Television Limited Warranty Mitsubishi Projection TV Limited WarrantyMitsubishi TV Software Page Page Connection Helpful Hints Mitsubishi Digital Electronics America, Inc 871D357B10