Mitsubishi Electronics HC2000 user manual Projectiing images, EN-20

Page 20

Viewing video images (continued)

C. Projectiing images

Preparation:

Remove the lens cap.

Turn on the power of the connected equipment.

 

POWER button/

 

 

 

POWER indicator

 

LAMP TEMP

POWER

 

 

 

 

 

 

Main power switch

AC IN

MAIN

 

 

 

 

 

LENS SHIFT

 

 

 

 

 

 

 

 

Lens shift dial

DOWN

 

UP

 

 

 

 

ZOOM IN / UP

 

 

ZOOM IN, OUT buttons

 

 

 

 

FOCUS -/LEFT

 

FOCUS +/RIGHT

FOCUS +/- buttons

ZOOM OUT / DOWN

 

 

 

 

AUTO

 

 

 

 

 

POSITION SOURCE MENU/EXIT

ENTER

 

 

 

 

 

 

SOURCE button

 

 

 

ON

STANDBY

 

ON( )button

 

 

AUTO OFF

LIGHT

 

 

 

 

 

 

 

DVI-A

 

SOURCE button

 

DVI-D

 

COMP

 

S-Video

Video

BNC

 

 

 

 

 

 

 

 

16:9

 

 

 

 

Standard

 

ZOOM

 

 

 

 

MEM2

 

 

 

 

MEM1

 

MEM3

{, } button

 

 

ZOOM IN/UP

 

 

FOCUS–/LEFT

 

FOCUS+/RIGHT

$, % button

 

 

ENTER

 

 

 

 

MENU ZOOM OUT/DOWN

 

 

 

 

BRIGHT

C.TEMP

 

 

 

CONT

 

 

 

 

 

 

 

 

 

 

COLOR

SHARP

 

 

 

TINT

 

 

 

 

 

 

1.Turn the main power switch to on (or to the I position).

• When the main power switch is turned on, the POWER

indicator lights up red.

LAMP TEMP POWER

Lighting in red

If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the main power switch is turned on. (The POWER indicator blinks red.) After the fan stops rotating, press the power button to turn back on the POWER indicator.

2.Press the POWER button on the projector or ON () button on the remote control.

LAMP TEMP POWER

 

LAMP TEMP POWER

Blinking

After about

Lighting in

1 minute.

in blue

blue

 

Power can not be turned “OFF”.

It may take about one minute for the lamp to light up.

The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

3.Select an input source.

Press the SOURCE button on the projector or any of the SOURCE buttons (such as DVI-D, DVI-A, and BNC) on the remote control that is corresponding to the terminal in use.

Switch the input source after an image is projected on the screen.

Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

Images may not be projected in the correct position, depending on the type of the input signal. In such a case, press the AUTO POSITION button on the projector or the AUTO button on the remote control. (See Page 21.)

4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See Page 11.)

When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See Page 11.)

6.Adjust the size of the projected image by pressing the ZOOM IN or OUT button on the projector or the remote control.

7.Adjust the focus by pressing the FOCUS+ or FOCUS- button on the projector or the remote control.

8.Adjust the image position by turning the lens shift dial of the projector.

Repeat steps 4 to 8, if necessary.

EN-20

Image 20
Contents Please read it before using your projector HC2000When using the projector in Europe EN-2Contents Important safeguards EN-4Never remove the cabinet Do not modify this equipmentIf you break or drop the cabinet Do not face the projector lens to the sunChecking accessories Preparating your projectorInserting the batteries into the remote ControlEN-7 OverviewControl area Power / indicators area Preparating your projector ContinueTerminal panel Bottom sideUsing the remote control Overview of the remote controlUsing the picture quality adjusting buttons EN-9Using the remote control Continue Operational range of the remote controlReception angle EN-10Setting up your projector Setting up the screenBasic setup Adjusting the projection angleSetting up your projector Continue When the aspect ratio of the screen isScreen size and projection distance EN-12EN-13 Connecting the projector to video equipment Connecting to a DVD playerViewing video images EN-14EN-15 Connecting to video equipment having a DVI-D terminalPlugging in the power cord Viewing video images Projectiing imagesEN-16 PreparationTo stop projecting EN-17EN-18 Setting the aspect ratioHow to change the settings Connecting the projector to a computer Plugging the power cordViewing computer images EN-19EN-20 When connecting to a notebook computer Example of the setting procedure for external outputAuto Position button Auto button EN-21Menu Operation EN-22How to set the menus EN-23EN-24 Available settings in the menusMenu operation Installation Menu EN-25To store the image quality settings To store the settingsTo enable the stored image quality settings EN-26Adjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessEN-28 Adjusting projected imagesTo adjust the tone of white Color Temp Special initial settings EN-29EN-30 Replacing the lampTo replace the lamp How to reset the lamp operating time EN-31Cleaning To clean the filterCleaning dust in the intake vent EN-32Asking for installation Dimension Drawings unit mmEN-33 To view images projected on the translucentEN-34 TroubleshootingNo image appears on the screen Problem Solution Images are not displayed correctly Problem Solution Others Problem SolutionProblem Solution EN-35EN-36 SpecificationsReplacement part Option / Not included in the box EN-37 Type of connectable signalsConnectors Mitsubishi Projector Contact Information North America