Mitsubishi Electronics HC2000 EN-35, Images are not displayed correctly Problem Solution

Page 35

Images are not displayed correctly.

Problem

Solution

 

 

Projected images are

• Adjust the projector and the screen so that they are perpendicular to each other.

distorted.

(See Page 11.)

Projected images are

• Adjust BRIGHTNESS and CONTRAST in the PICTURE menu. (See Page 27.)

dark.

• Replace the lamp. (See Pages 30 and 31.)

 

 

Projected images are

• Adjust the focus. (See Pages 16 and 20.)

blurred.

• Check that the lens cap is removed.

 

• Clean the lens.

 

• Adjust TRACKING and FINE SYNC. in the SIGNAL SETTING menu. (See

 

Page 29.)

 

• Adjust BRIGHTNESS and CONTRAST in the PICTURE menu. (See Page 27.)

 

• Adjust the projector and the screen so that they are perpendicular to each other.

 

(See Page 11.)

White dots are seen

• This symptom is normal for a DLP projector and is not a malfunction. (A very

on projected images.

small number of pixels may stay lit or out, but such symptom is not a malfunction.

Black dots are seen

Pixels of 99.99% or more are effective.)

on projected images.

 

 

 

Rainbow effect is

• This is due to color breaking noise that occurs in a DLP system and is not a

seen on projected

malfunction.

images.

 

Fine streaks are seen

• This is due to interference with the screen surface and is not a malfunction.

on projected images.

Replace the screen or displace the focus a little.

 

 

Projected images

• Connect the plugs of the cables to external devices securely.

become wavy.

• Keep the projector away from devices that emit interfering radio waves.

 

 

Hue is not

• Check that COMPONENT in the INSTALLATION menu has been set correctly.

appropriate.

(See Page 25.)

 

• Check that the cables connected to the external devices are not broken.

 

 

Others

 

 

 

Problem

Solution

 

 

The exhaust vents

• This air comes out after cooling the inside of the projector. You may feel hot, but

emit warm air.

this is not a malfunction.

Menus cannot be set.

• Being affected by noise, the microcomputer inside the projector may be working

 

wrongly.

 

➔ Turn off the power, wait for two minutes, and then turn it back on.

 

• When you cannot turn off the power, turn off the main power, leave the projector

 

alone for at least 20 minutes, and then turn back on the power.

Abnormal sound is

• Because the color wheel spins at a high speed, metallic sounds may be heard in

heard.

rare occasions. Such symptom is not a malfunction.

 

 

If the following problem occurs after the lamp is replaced, check the following first.

Problem

Solution

 

 

The projector does

• Fit the lamp cover securely. (See Pages 30 and 31.)

not turn on.

• Reset the lamp operating time. (See Page 31.)

 

 

ENGLISH

EN-35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents HC2000 Please read it before using your projectorEN-2 When using the projector in EuropeContents EN-4 Important safeguardsDo not face the projector lens to the sun Never remove the cabinetDo not modify this equipment If you break or drop the cabinetControl Checking accessoriesPreparating your projector Inserting the batteries into the remoteEN-7 OverviewControl area Bottom side Power / indicators areaPreparating your projector Continue Terminal panelEN-9 Using the remote controlOverview of the remote control Using the picture quality adjusting buttonsEN-10 Using the remote control ContinueOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupEN-12 Setting up your projector ContinueWhen the aspect ratio of the screen is Screen size and projection distanceEN-13 EN-14 Connecting the projector to video equipmentConnecting to a DVD player Viewing video imagesEN-15 Connecting to video equipment having a DVI-D terminalPlugging in the power cord Preparation Viewing video imagesProjectiing images EN-16EN-17 To stop projectingEN-18 Setting the aspect ratioHow to change the settings EN-19 Connecting the projector to a computerPlugging the power cord Viewing computer imagesEN-20 EN-21 When connecting to a notebook computerExample of the setting procedure for external output Auto Position button Auto buttonEN-22 Menu OperationEN-23 How to set the menusEN-24 Available settings in the menusMenu operation EN-25 Installation MenuEN-26 To store the image quality settingsTo store the settings To enable the stored image quality settingsTo sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintEN-28 Adjusting projected imagesTo adjust the tone of white Color Temp EN-29 Special initial settingsEN-30 Replacing the lampTo replace the lamp EN-31 How to reset the lamp operating timeEN-32 CleaningTo clean the filter Cleaning dust in the intake ventTo view images projected on the translucent Asking for installationDimension Drawings unit mm EN-33EN-34 TroubleshootingNo image appears on the screen Problem Solution EN-35 Images are not displayed correctly Problem SolutionOthers Problem Solution Problem SolutionEN-36 SpecificationsReplacement part Option / Not included in the box EN-37 Type of connectable signalsConnectors North America Mitsubishi Projector Contact Information
Top Page Image Contents