Mitsubishi Electronics X100 manual User Presets menu, Simple way of adjustment

Page 32

Menu operation (continue)

USER PRESETS menu

If you select USER and press the ENTER button, the user setting menu appear.

HELP

USER

H-POS / V-POS

TRACKING

WIDTH / HEIGHT

FINE

CLAMP

RGB/

 

PRESETS

SYNC

Y,Cb,Cr

 

 

 

NORMAL

 

 

H-POS

 

WIDTH

 

 

 

 

 

 

 

 

 

 

 

 

 

ENHANCED

 

 

 

 

HEIGHT

 

 

RGB

MEMORY

POINTER

 

V-POS

0

0

0

0

0

 

Y,Cb,Cr

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

 

 

OPTION

 

0

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

QUIT

RETURN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H-POSUse to adjust the horizontal position of the image. The image moves to the right as the number increases.

V-POSUse to adjust the vertical position of the image. The image moves down as the number increases.

TRACKING Use to match the clock signals of the projector with the input signal to avoid image noise such as wide stripes.

HEIGHT Use to adjust the height of the image. The image size grows higher as the number increases. (Normally, there is no need for adjustments.)

WIDTH Use to adjust the width of the image. The image size grows wider as the number increases. (Normally, there is no need for adjustments.)

FINE Use to synchronize the projector with PC input signals so that the image is not

SYNC blurred.

CLAMP Use to adjust the level of luminance. The projector does not need this adjustment for ordinary use. If you use a PC video card or something similar, the lighter colors of the projected image may become blurred. In this case, adjust CLAMP.

RGB /

When the equipment (DVD player system, etc.) with Y, Cb, Cr connectors is con-

Y, Cb, Cr

nected to the PC-1 or PC-2 connector, select [Y, Cb, Cr]. Depending on the DVD

 

player, the image may not be projected correctly with this projector.

The simple way of adjustment

1.Horizontal position:

Adjust the start position (the left end) using H-POS, and adjust the end position (the right end) using TRACKING. Then repeat these steps.

2.Vertical position:

Adjust the start position using V-POS.

If you change the settings of the USER PRESETS, you must select MEMORY and press the ENTER button.

The projector is able to memorize 2 signals setting. When reached over 2, settings of the signals will be deleted in chronologic order.

By pressing the + button, you can change the setting among the default condition and memorized condition.

32

Image 32
Contents X100 Page Compliance Notice of FCC Contents Important safeguards Important safeguards Never remove the cabinet Do not modify this equipmentIf you break or drop the cabinet Do not face a lens to the sunOverview of the projector FINE, ADJUST, FOCUS/ZOOM and Auto buttons Left side Bottom side Overview of the remote control Battery installation Preparing the projector for operation Orientation of the projectorAdjusting the angle of projection Getting ready for projectionScreen Ground terminalBasic connections AT VGACables and adapters Order of turning on / offDesktop computer Basic connections continueProjector + IBM PC or IBM PC compatibles DOS Power Book When outputting to both a PC monitor and the projectorProjector + Macintosh DesktopDesktop computer display connector Projector + NEC PC-98 and Epson PC seriesProjector + AV equipment To operate projector power on Auto buttonTurning off the projector VIDEO1 VIDEO2 RGB1Menu operation Menu layersBasic operation Example Brightness adjustment 3 2,4Menu operation continue Normal menuGamma Correction menu Enhanced menu ReverseSuper Pointer menu Audio menuReceive Auto Power OFF Option menuUser Presets menu Simple way of adjustmentAdvanced feature for presentation Cursor operationExpand Super impose Picture in Picture Using the PC-CARD Setting up / replacing the PC-CARDEmergency capture from projector source Play backPage Advanced feature with PC EnvironmentInstallation of software Command referencePCV PC Card Viewer Starting up PC Card ViewerReturn button Delay time button Capture button Recording the imageEditing the presentation Pcgc Personal Computer Graphic Control ConnectionIndicator and main menu control window Power button and indicatorIndicators Starting up PcgcRemote control window Sub menu control windowOperation of PC by remote control SpacePointerSetting of SpacePointer Uninstallation of softwareEnable/Disable Port selectionMaintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensReplacement of a light source lamp Purchase of the light source lamp Life of the lampIndicators / TEMP, LAMP, Power Indicator Shows Condition Possible SolutionsTroubleshooting Problems Cause Possible SolutionsImage Specifications Rated input LCD panelsWhat’s included in the box Replacement parts listAccessories Mitsubishi Electronics AMERICA, INC