One for All URC10820N warranty Using Channel Scan, Programming Favorite Channel Scan

Page 12

Using Channel Scan

In the TV, VCR, DVD, CBL and SAT modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed, “Programming Favorite Channel Scan”) and/or all channels for the selected mode.

1.Press TV, VCR, DVD, CBL or SAT once.

2.Press FAV once.

•If Favorite Channel Scan has been set up, scanning of favorite channels will start and cycle through stored channels, then proceed to the next channel up and cycle through all channels on the selected device.

•If Favorite Channel Scan has not been set up, scanning will start with the current channel, then proceed to the next channel up and cycle through all channels on the selected device.

3.To stop scanning channels at any time, press any key once.

Programming Favorite Channel Scan

In the TV, VCR, DVD, CBL and SAT modes, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when you press FAV (see “Using Channel Scan”).

NOTE: Only channels of one mode can be stored for Favorite Channel Scan.

1.On the remote control, press TV, VCR, DVD, CBL or SAT once.

2.Press and hold SET until the LED (red light) blinks twice, then release SET.

3.Enter 9 9 6. The LED will blink twice.

4.Use the keypad to enter a favorite channel number (e.g., 031). Then press SET once.

NOTE: If the original remote control required pressing an ENTER key to change the channel, also press the ENTER key after the channel number (e.g., 0 3 1 ENTER).

5.If desired, repeat step 4 (in this section) for each favorite channel to be stored, up to a total of 10 channels.

NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming.

6.To exit programming, press and hold SET for 3 seconds. The LED will blink twice.

Re-Assigning Device Keys

You can set this remote to control a second TV, VCR, DVD player, or other device. For example, to control a TV, a cable box, and two DVDs, you will need to re-assign the unused AUX1 key to operate the second DVD as follows:

1.On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 9 2. The LED will blink twice.

3.Press DVD once, then press AUX1 once.

4.The AUX1 key is now ready to be programmed for your second DVD. See “Setting Up Your Components.”

To re-assign other device keys to the AUX1 key, repeat steps 1 through 4 by substituting the sequence from the following chart:

To Re-Assign Device

Perform Sequence

 

 

 

AUX1 as 2nd TV key:

SET - 9 - 9 - 2

- TV - AUX1

 

 

 

AUX1 as 2nd VCR key:

SET - 9 - 9 - 2

- VCR - AUX1

 

 

 

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Contents ContenidoInstalling Batteries Features and FunctionsIntroduction Key Charts Device Table Device Controls These Devices KEYSetting Up Your Components Programming Combo Device Control AUX1 CodeAUX2 Code To control a TV/DVD ComboSearching For Your Code Checking the CodesUsing Learning Learning PrecautionsProgramming a Learning Key Deleting Functions From The Learning KeysChanging Volume Lock Locking Volume Control To One Mode Global Volume LockUnlocking All Volume Control Restoring Default Setting Programming a Master Power Macro To Program the Master Power MacroTo Operate Master Power Macro Programming a Favorite ChannelProgramming a Macro On a Device Key Clearing a MacroTo Program the Device Key Macro To Operate the Device Key MacroUsing Channel Scan Programming Favorite Channel ScanRe-Assigning Device Keys Using Keymover Restoring Keymoved Keys To Default SettingsProgramming Keymover Restoring a Single Keymoved KeyRestoring Factory Default Settings TroubleshootingRestoring All Keymoved Keys in a Single Mode Care and Maintenance FCC ComplianceAdditional Information Limited Lifetime Warranty Introducción Instalación de las BateríasCaracterísticas y Funciones Funciones de las Teclas Tabla de Dispositivos Tecla DE Controla Estos DispositivosProgramación de un Dispositivo Aparato DVD, VCR, DVD/R, HTIB, DVD/VCRProgramación de un Aparato Combinado Para controlar un aparato combinado TV/DVDBúsqueda de su Código Verificación de los CódigosUso de la Función Aprendizaje Precauciones sobre la Función AprendizajeProgramación de una Tecla de Aprendizaje Cambio del Bloqueo del Volumen Borrar Funciones de las Teclas de AprendizajeUso de los Macros Programación de un Macro de Canal FavoritoProgramación de Un Macro en una Tecla de Dispositivo Para Programar el Macro de Tecla de DispositivoUso del Macro de Tecla de Dispositivo Uso de la Exploración de Canales Programación de una Exploración de Canales FavoritosReasignación de las Teclas de Dispositivos Borrar un MacroUso de la Función Keymover Programación de la Función KeymoverRestauración de los Valores Fijados en la Fábrica Localización de FallasRestauración de una Sola Tecla Mudada Restauración de Todas las Teclas Mudadas en un Solo ModoConformidad con la FCC Información AdicionalCuidado y Mantenimiento Garantía Limitada durante la Vida Útil del ProductoPage Audio DTV ConvertersRécepteurs TV numériques Convertidores DigitalesVCRs / Magnétoscopes DVD / Lecteurs DVDPVRs DVRs
Top Page Image Contents