One for All URC10820N Using Keymover, Programming Keymover, Restoring a Single Keymoved Key

Page 13

To Re-Assign Device

Perform Sequence

 

 

AUX1 as 2nd CBL key:

SET - 9 - 9 - 2 - CBL - AUX1

 

 

AUX1 as 2nd SAT key:

SET - 9 - 9 - 2 - SAT - AUX1

 

 

 

AUX1 as 2nd CD key:

SET - 9 - 9 - 2

- CD - AUX1

 

 

 

AUX1 as 2nd PVR key:

SET - 9 - 9 - 2

- PVR - AUX1

 

 

 

AUX1 as 2nd AUD key:

SET - 9 - 9 - 2

- AUD - AUX1

 

 

 

AUX1 as 2nd AUX2 key:

SET - 9 - 9 - 2

- AUX2 - AUX1

 

 

 

You can also re-assign another unused device key by substituting an open key for the AUX1 key in the above chart and performing the sequence. For example, to re-assign an unused CBL key as a 2nd CD key, perform SET - 9 - 9 - 2 - CD CBL. When a re-assignment is done, the LED (red light) will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see “Setting Up Your Components”).

Using Keymover

This remote includes a Keymover feature that allows you to map (or copy) keys from one mode (i.e., source mode) to another mode (i.e., destination mode).

NOTE: The following keys cannot be used as a source or

destination: TV, CBL, SAT, VCR, DVD, CD, PVR, AUD, AUX1, AUX2, FAV, and SET.

Programming Keymover

For example, if your VCR does not have volume control, you can map those keys (i.e., VOL +, VOL -, and MUTE) from the TV mode to the VCR mode as follows:

1.Press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 9 4. The LED will blink twice.

3.For the source mode, press TV once.

4.For the source key, press VOL + once.

5.For the destination mode, press VCR once.

6.For the destination key, press VOL + once.

7.The LED will blink twice, indicating the keymoved sequence is correct.

8.Repeat steps 1 through 7 twice more to map remaining volume control keys, substituting VOL - and MUTE as source and destination keys in steps 4 and 6.

Upon completion of the above procedure, you can now use this remote to control the TV’s volume and MUTE in the VCR mode, as well as in the TV mode.

Restoring Keymoved Keys To Default Settings

Restoring a Single Keymoved Key

1.Press a device key that has a keymoved key.

2.Press and hold SET until the LED (red light) blinks twice, then release SET.

3.Enter 9 9 4. The LED will blink twice.

4.Press the destination key twice (where the keymoved key is stored). The LED will blink twice.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Contenido ContentsFeatures and Functions Installing BatteriesIntroduction Key Charts Device Controls These Devices KEY Device TableSetting Up Your Components AUX1 Code Programming Combo Device ControlAUX2 Code To control a TV/DVD ComboChecking the Codes Searching For Your CodeLearning Precautions Using LearningProgramming a Learning Key Deleting Functions From The Learning KeysLocking Volume Control To One Mode Global Volume Lock Changing Volume LockUnlocking All Volume Control Restoring Default Setting To Program the Master Power Macro Programming a Master Power MacroTo Operate Master Power Macro Programming a Favorite ChannelClearing a Macro Programming a Macro On a Device KeyTo Program the Device Key Macro To Operate the Device Key MacroProgramming Favorite Channel Scan Using Channel ScanRe-Assigning Device Keys Restoring Keymoved Keys To Default Settings Using KeymoverProgramming Keymover Restoring a Single Keymoved KeyTroubleshooting Restoring Factory Default SettingsRestoring All Keymoved Keys in a Single Mode FCC Compliance Care and MaintenanceAdditional Information Limited Lifetime Warranty Instalación de las Baterías IntroducciónCaracterísticas y Funciones Funciones de las Teclas Tecla DE Controla Estos Dispositivos Tabla de DispositivosDVD, VCR, DVD/R, HTIB, DVD/VCR Programación de un Dispositivo AparatoPara controlar un aparato combinado TV/DVD Programación de un Aparato CombinadoVerificación de los Códigos Búsqueda de su CódigoPrecauciones sobre la Función Aprendizaje Uso de la Función AprendizajeProgramación de una Tecla de Aprendizaje Borrar Funciones de las Teclas de Aprendizaje Cambio del Bloqueo del VolumenProgramación de un Macro de Canal Favorito Uso de los MacrosPara Programar el Macro de Tecla de Dispositivo Programación de Un Macro en una Tecla de DispositivoUso del Macro de Tecla de Dispositivo Programación de una Exploración de Canales Favoritos Uso de la Exploración de CanalesReasignación de las Teclas de Dispositivos Borrar un MacroProgramación de la Función Keymover Uso de la Función KeymoverLocalización de Fallas Restauración de los Valores Fijados en la FábricaRestauración de una Sola Tecla Mudada Restauración de Todas las Teclas Mudadas en un Solo ModoInformación Adicional Conformidad con la FCCGarantía Limitada durante la Vida Útil del Producto Cuidado y MantenimientoPage DTV Converters AudioRécepteurs TV numériques Convertidores DigitalesDVD / Lecteurs DVD VCRs / MagnétoscopesPVRs DVRs
Top Page Image Contents