One for All URC10820N warranty Restoring Factory Default Settings, Troubleshooting

Page 14

Restoring All Keymoved Keys in a Single Mode

1.Press and hold SET until the LED (red light) blinks twice.

2.Enter 9 9 4. The LED will blink twice.

3.Press the destination mode twice (where keymoved keys are stored). The LED will blink twice.

Restoring Factory Default Settings

This remote includes a Setup Code Reset program. You can use it to restore all your programmed codes to factory settings and delete all custom programming.

IMPORTANT: Executing this program erases all code settings and all custom settings including, Macros, Learned Keys, Reassigned Device Keys, Keymoved Keys, Favorite Channels, and all device settings.

1.On the remote control, press and hold SET until the LED (red light) blinks twice.

2.Enter 9 8 0. The LED will blink four times.

3.Your remote is now ready for programming.

Troubleshooting

LED (red light) does not blink when you press a key.

Replace batteries with four new AAA alkaline batteries.

LED (red light) blinks five times after you press a key.

Replace batteries with four new AAA alkaline batteries.

LED blinks when you press a key, but home entertainment device does not respond.

Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away.

The unit does not control home entertainment devices or commands are not working properly.

Try all listed codes for the device brands being set up. Make sure they can be operated with an infrared remote control.

TV/VCR Combo does not respond properly.

Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation.

Changing channels does not work properly.

If the original remote control required pressing ENTER to change channels, then press ENTER on the remote control after entering the channel number.

During learning, LED emits a long blink after pressing and holding key to be learned.

Memory is full or a bad capture has occurred. Avoid high-ambient light sources, such as direct daylight and fluorescent bulbs. Try readjusting positions of remote controls before performing the procedure again.

Tried Searching For Your Code method and still could not find a working code.

Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release.Next enter 9 9 2. Then press the device key to be cleared twice.Now repeat the Searching for Your Code method.

No remote control of volume.

See “Changing Volume Lock” to lock/ unlock volume.

If the above does not work.

Please visit: www.oneforall.com

Consumer Help Line: 1 (800) 315-0990

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Contents ContenidoIntroduction Installing BatteriesFeatures and Functions Key Charts Device Table Device Controls These Devices KEYSetting Up Your Components AUX2 Code Programming Combo Device ControlAUX1 Code To control a TV/DVD ComboSearching For Your Code Checking the CodesProgramming a Learning Key Using LearningLearning Precautions Deleting Functions From The Learning KeysUnlocking All Volume Control Restoring Default Setting Changing Volume LockLocking Volume Control To One Mode Global Volume Lock To Operate Master Power Macro Programming a Master Power MacroTo Program the Master Power Macro Programming a Favorite ChannelTo Program the Device Key Macro Programming a Macro On a Device KeyClearing a Macro To Operate the Device Key MacroRe-Assigning Device Keys Using Channel ScanProgramming Favorite Channel Scan Programming Keymover Using KeymoverRestoring Keymoved Keys To Default Settings Restoring a Single Keymoved KeyRestoring All Keymoved Keys in a Single Mode Restoring Factory Default SettingsTroubleshooting Additional Information Care and MaintenanceFCC Compliance Limited Lifetime Warranty Características y Funciones IntroducciónInstalación de las Baterías Funciones de las Teclas Tabla de Dispositivos Tecla DE Controla Estos DispositivosProgramación de un Dispositivo Aparato DVD, VCR, DVD/R, HTIB, DVD/VCRProgramación de un Aparato Combinado Para controlar un aparato combinado TV/DVDBúsqueda de su Código Verificación de los CódigosProgramación de una Tecla de Aprendizaje Uso de la Función AprendizajePrecauciones sobre la Función Aprendizaje Cambio del Bloqueo del Volumen Borrar Funciones de las Teclas de AprendizajeUso de los Macros Programación de un Macro de Canal FavoritoUso del Macro de Tecla de Dispositivo Programación de Un Macro en una Tecla de DispositivoPara Programar el Macro de Tecla de Dispositivo Reasignación de las Teclas de Dispositivos Uso de la Exploración de CanalesProgramación de una Exploración de Canales Favoritos Borrar un MacroUso de la Función Keymover Programación de la Función KeymoverRestauración de una Sola Tecla Mudada Restauración de los Valores Fijados en la FábricaLocalización de Fallas Restauración de Todas las Teclas Mudadas en un Solo ModoConformidad con la FCC Información AdicionalCuidado y Mantenimiento Garantía Limitada durante la Vida Útil del ProductoPage Récepteurs TV numériques AudioDTV Converters Convertidores DigitalesPVRs DVRs VCRs / MagnétoscopesDVD / Lecteurs DVD
Top Page Image Contents