3Com 11.3 manual Using the Backup, Flash Card

Page 11

Using the Backup Flash Card

11

2Format the blank flash memory card in drive B by entering:

FORMAT b:

Type Y for yes when the formatting confirmation message is displayed.

3Create a directory on the formatted flash memory card by entering:

MakeDir b:\primary

4Copy the software from the Enterprise OS software flash memory card in drive A to the formatted flash memory card in drive B by entering:

COpy a:\primary\* b:\primary

 

 

PACKET POWER/

A

ATUS

FORWARD FAULT

RESET ATTENTION

 

B

2

3

4

 

Copy contents of drive A to the directory you created on drive B

5After you have copied the software, replace the original Enterprise OS software flash memory card in drive A with the backup copy from drive B.

 

 

PACKET

POWER/

RESET

A

ATUS

FORWARD

FAULT

ATTENTION

2

3

4

 

 

B

 

 

 

Replace original card in drive A with new copy from drive B.

Keep the original card as a backup.

Keep the original Enterprise OS software flash memory card in a safe place and protect it from accidental damage. The original is your backup in the rare event that the Enterprise OS software or the backup flash memory card becomes corrupted. See ”Using the Backup Flash Card” on page 11 for instructions on installing the backup flash memory card.

6The Enterprise OS software boot files for a DPE module are factory shipped with a:/primary/boot.29k as the default primary boot source. If you have installed the Enterprise OS software on drive A, and you want to keep the same boot file as the boot source, reboot your NETBuilder II bridge/router by entering:

ReBoot

7If you want to configure your primary boot source to a drive and file other than the default, see Chapter 3 for instructions on configuring the boot source for the NETBuilder II bridge/router.

Using the Backup

If the Enterprise OS software has been corrupted and you need to reboot, use

Flash Card

your original Enterprise OS software flash memory card to reset your system by

 

following these steps:

1

Remove the corrupted flash memory card from the DPE module.

2

Insert the original Enterprise OS software flash memory card into drive A on the

 

DPE module.

Image 11
Contents New Installation for Enterprise OS Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, CaliforniaContents 3COM Corporation Limited Warranty This Guide How to UseAbout this Guide IntroductionConvention Description ConventionsList conventions that are used throughout this guide Icon Alerts you toThis guide apply to all software packages flash memory card for first time NETBuilder II installationsOverview SoftwareChange the primary boot source default as needed Install System Software and Boot See ChapterInstall software from a flash memory card Change the Primary Boot Source See ChapterFlash Memory Card Installing Software and Booting Netbuilder II SystemInstalling Software Performing Initial Boot Booting fromNETBuilder II System Making a BackupFlash Memory CardFlash Card Using the BackupPress Reset buttons to reboot Command Changing the Boot SourceUsing the Boot Configuring Primary Boot SourceAt the Enterprise OS prompt, enter Primary Boot Source menu is displayedChanging the Boot Source System Configuring Basic SettingsLogging on to User Interfaces Setting Up IP RoutingLearning About Application Menu-Driven Versus of three ways Command-Line InterfaceWeb Link Interface Description Log in as root. TypeMain menu Level 1 is displayed Abbreviated Syntax Full-Form SyntaxSymbol Description SymbolsCan be shortened by abbreviating it to Full and Abbreviated Syntax ExamplesCan be abbreviated to Determining the Display of Ports and Virtual Ports Variations in Command SyntaxEntering Service Names in Command Lines Command History Substitution Using AliasesPrivilege Level Strings Syntax for Assigning ValuesNumeric Values NamesPort and Path Naming Restrictions Media Addresses An example of a Frame Relay address Bridge/router or tunnel switches. In the global addressingAsynchronous Transfer Mode ATM address Decimal. The Dlci identifies a virtual circuit on the FrameNetwork Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following exampleGetting Help Level PasswordObtaining Network Manager PrivilegeInformation Setting the Time and DateSetting System AdministratorSETDefault -SYS SysCONtact = John Smith 408 IPX OSI Assign Internet addresses to individual ports usingAssigning an IP Address to a bridge/router Port DELete -SNMP COMmunity Anycom COMmunity Enable the Snmp service by enteringRemoteManager Configuring Basic Settings Online Technical ServicesTechnical Support 408 727 Access by Analog ModemAccess by Digital Modem 847 262Latin America Country Telephone Number Asia Pacific RimEurope Europe, South Africa, and Middle EastCountry Telephone Number Fax Number Numerics IndexSnmp Snmp 3Com Corporation Limited Warranty Disclaimer