3Com 11.3 manual At the Enterprise OS prompt, enter, Primary Boot Source menu is displayed

Page 15

Configuring the Primary Boot Source

15

4At the Enterprise OS prompt, enter:

SysconF 2

The Primary Boot Source menu is displayed:

Primary Boot Source:

 

1.

Boot Filename:

a:/primary/boot.29k

2.

Config File Source

a:/primary

3.

IP Addresses

Client:none Subnet Mask:none

4.

FTP Login Parameters

 

Enter parameter number or press Q to quit:

5Enter 1 to select a boot filename.

Information similar to the following is displayed:

Current Boot Filename: a:/primary/boot.29k

Enter Boot Filename (CR = no change):

6Enter a new boot filename (such as b:/primary/boot.29k) and press the Return key.

The configuration files must reside on the same drive as the boot source. If the drive you specify is different from the configuration boot source drive, you are prompted to change the configuration file source to the same drive.

If the boot drive you specify conflicts with the one set in the Dump Destination parameter, you are prompted for a different drive.

7Enter q to quit the menu.

The System Configuration menu showing the new entries is displayed:

System Configuration

 

1.

Serial Ports

Console: 9600

2.

Primary Boot Source

b:/primary/boot.29k, b:/

3.

Secondary Boot Source

b:/secondar/boot.29k, b:/

4.

Test Boot Source

a:/primary/boot.29k, a:/:

5.

Boot Sources

Primary and Secondary

6.

Dump Destination

Partial dump only

7.Recovery Procedure

8.MP Boot Source

9. Boot StatisticsBooted: 1 Exceptions: 0 Enter parameter number or press Q to quit:

8Enter q to quit the configuration program.

9At the prompt, enter:

ReBoot

The NETBuilder II bridge/router reboots using the newly established drive B as the primary boot source.

For drive B to function as the boot source, a flash memory card with software version 11.3 must be installed in drive B.

Image 15
Contents New Installation for Enterprise OS Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, CaliforniaContents 3COM Corporation Limited Warranty This Guide How to UseAbout this Guide IntroductionConvention Description ConventionsList conventions that are used throughout this guide Icon Alerts you toThis guide apply to all software packages flash memory card for first time NETBuilder II installationsOverview SoftwareChange the primary boot source default as needed Install System Software and Boot See ChapterInstall software from a flash memory card Change the Primary Boot Source See ChapterFlash Memory Card Installing Software and Booting Netbuilder II SystemInstalling Software Performing Initial Boot Booting fromNETBuilder II System Making a BackupFlash Memory CardFlash Card Using the BackupPress Reset buttons to reboot Changing the Boot Source Using the BootCommand Configuring Primary Boot SourceAt the Enterprise OS prompt, enter Primary Boot Source menu is displayedChanging the Boot Source Configuring Basic Settings Logging on toSystem Setting Up IP Routing Learning AboutUser Interfaces Application Menu-Driven Versus of three ways Command-Line InterfaceWeb Link Interface Description Log in as root. TypeMain menu Level 1 is displayed Abbreviated Syntax Full-Form SyntaxSymbol Description SymbolsFull and Abbreviated Syntax Examples Can be abbreviated toCan be shortened by abbreviating it to Variations in Command Syntax Entering Service Names in Command LinesDetermining the Display of Ports and Virtual Ports Command History Substitution Using AliasesPrivilege Level Strings Syntax for Assigning ValuesNumeric Values NamesPort and Path Naming Restrictions Media Addresses An example of a Frame Relay address Bridge/router or tunnel switches. In the global addressingAsynchronous Transfer Mode ATM address Decimal. The Dlci identifies a virtual circuit on the FrameNetwork Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following exampleGetting Help Level PasswordObtaining Network Manager PrivilegeInformation Setting the Time and DateSetting System AdministratorSETDefault -SYS SysCONtact = John Smith 408 IPX OSI Assign Internet addresses to individual ports usingAssigning an IP Address to a bridge/router Port DELete -SNMP COMmunity Anycom Enable the Snmp service by entering RemoteManagerCOMmunity Configuring Basic Settings Services Technical SupportOnline Technical 408 727 Access by Analog ModemAccess by Digital Modem 847 262Latin America Country Telephone Number Asia Pacific RimEurope Europe, South Africa, and Middle EastCountry Telephone Number Fax Number Numerics IndexSnmp Snmp 3Com Corporation Limited Warranty Disclaimer