EverFocus EDSR-600, EDSR-400 instruction manual Operation, Insert a HDD IDE for Video Storage

Page 13

Operation

5. Operation

(1) Insert a HDD (IDE) for Video Storage

Insert one or two HDD (3.5” IDE) for Video Storage.

The HDD should be set as Master. (Set Cable Select is also available) (Normally the default setting of HDD is Master)

Note: After hard disk case is inserted into the hard disk tray, be sure to turn the tray key in lock position.Otherwise, HDD will not be detected.

ATTENTION: Changing HDD s and switching on HDD s is not allowed during recording!

(2)Connect cable for video/audio input and video/audio out, The detail connection is described in SYSTEM CONNECTION.

(3)Switch Power On

The LCD panel in the front panel will light when you switch on the power.

(4)Press MENU key to enter SET UP MENU.

Once inside the main menu you will find there are 14 set up pages as below:

Selected item will be surrounded by a white block.

MENU

MAIN MENU

CLOCK

TIMER

SEQUENCE

TITLE

COVERT

ALARM

MOTION

RECORD

NETWORK

CONTROL

BUZZER

ARCHIVE

CALL

DISK

SYSTEM

(5)	Turn the JOG dial clockwise or counter-clockwise to select the item,
	press ENTER key for detail set up for each item.

(6) Press MENU again to leave the set up menu.

8

Image 13

Contents V1.05 2004/3/25 EDSR-600Safety Precautions Power Disconnect Important Safeguards Important SafeguardsTable of Contents Product Overview Product OverviewSpecifications SpecificationsBack Panel Connections Back Panel ConnectionsON/OFF VideoAlarm I/O Refer pin assignment in Appendix-D, System Connection Before InstallationSystem Connection Front Panel Keypads Front Panel KeypadsShuttle Ring and JOG Dial Chanel KeysIR Remote Controller receiver Operation Press Menu key to enter SET UP MenuOperation Insert a HDD IDE for Video StorageMenu Flow Menu flowCall CLOCK/LANGUAGE Setting Menu , we define Clock Setting MenuWrong DLY Start 2000 Stop Correct DLY Start 2000 Stop Timer Setting MenuSequence Setting MENU, we define for Main Monitor Sequence Setting MenuTitle Setting Menu , we define Title Setting MenuCovert Setting Menu , we define Covert Setting MenuDefault setting is OFF for all cameras Alarm Recording MENU, we define Alarm Record Setting MenuMotion Record Setting MENU, we define Motion Setting MenuOP Operation Default OFF Press 1-4/6 to Manual Edit Record Setting Menu Network Setting MENU, we define Network Setting MenuUSER-NAME Password Level MAC AddressControl Setting MENU, we define Control Setting MenuBuzzer Setting Menu Picture Size Archive Setting MenuTime Stamp Water MarkCH, DWELL, Event Call Monitor Setting MenuDisk Setting MENU, we define Disk Setting MenuDisk Usage HDD-1, HDD-2 System Setting MENU, we define System Setting MenuPlay with Audio AUDIO-1, AUDIO-2 Recording Alarm RecordingInstant Recording RECNormal Playback Playing BackPlay PauseSearch Playback Search PlaybackSearch EnterAlarm List search playback Search Stop Date/Time Search PlaybackStill Image Copy Data ExportPause Copy Menu Copy to Movie FileExport Event LOG List AlarmPress „DISPLAY key and hold key for about 2 seconds DisplayMonitor Views / Operation Mode Display ZoomCall monitor Main MonitorCall Monitors Setting Call Monitor11.1 RS-485 Remote Control Remote ControlRJ45 RS485 pin assignment IR Remote Controller optional IR Remote ControllerEDSR600 Channel keys #1~6 #1~16 valid for EDSR900/1600 only View From Internet/Intranet Main Screen View From Internet/Intranet View From Internet/Intranet Appendix-A SpecificationsAppendix-B ? When Recording with 160GB HDDEstimated with typical image-low noise level 59259.3 ? When Recording with 320GB HDDDVR Appendix C Serial Interface SpecificationsHost Sample control code packets Remote Control ProtocolLength Byte Format of message packet is as followsReceiver ID OPcode Opcode Byte & Data bytesRemote keys OPcode=0x4B Checksum ByteAppendix-D Alarm I/O pin assignmentPIN # ALM1~ALM4 EDSR400, ALM1~ALM6 EDSR600Beijing Office Head Office European OfficeUSA Office Japan Office