Maxtor Built in Digital Video Recorder Record Setup, Record Configuration, Multiplex, Super Fine

Page 27

5-4. RECORD SETUP

This is the most important configuration of the DVR. Enter into SYSTEM MENU-RECORD SETUP and press the [ENTER] button.

1) RECORD CONFIGURATION

Use direction button to move and [-] [+] button to set value.

(1)OVERWRITE : Set overwrite or stop recording when the HDD is full.

(2)MULTIPLEX

-DUPLEX : Playback & Ethernet

-TRIPLEX : Playback & Recording & Ethernet

Note: DUPLEX MODE is recommended to playback the images at a maximum frame rate.

But, it makes DVR not to record during search.

(3)QUALITY : Set recording picture quality.

Actually it is fixing maximum data size of image for each picture quality in 5 steps as follows.

-BASIC

-NORMAL

-ENHANCED

-FINE

-SUPER FINE: Default quality set by manufacturer

In Emergency recording mode, recording quality is

SUPER FINE.

CHAP. 5 Set Up

RECORD SETUP

RECORD CONFIGURATION

SCHEDULE SETUP

HOLIDAY SETUP

SELECT MENU : ▲▼, & [ENTER]

RECORD CONFIGURATION

OVERWRITE

ON

MULTIPLEX

TRIPLEX

QUALITY

ENHANCED

RESOLUTION

60IPS 720*240

RECORD IN ALARM

1/1X

RECORD IN MOTION

1/1X

CONTINUOUS RECORD

1/1X

 

 

SELECT MENU : ▲▼, CHANGE VALUE : + -

To send more images via IP network and longer recording time, set QUALITY at NORMAL or ENHANCED and record at 360x240(360x288).

Data size of image in PAL system is a little bigger than NTSC system, but the total recording time is same as in NTSC system.

(4)RESOLUTION : Set recording resolution.

- 60 ips at 720x240(NTSC) , 50 ips at 720x288(PAL)

-120 ips at 360x240(NTSC) , 100 ips at 360x288(PAL)

It is not possible to see those images in full screen mode in playback.

Recording in Dual resolution is recommended for higher recoding speed, and also to send more images via IP network.

(5)RECORD IN ALARM : Set record speed (skip rate) in ALARM record mode.

(6)RECORD IN MOTION : Set record speed (skip rate) in MOTION record mode.

(7)CONTINUOUS RECORD : Set record speed (skip rate) in CONTINUOUS record mode.

Set record speed (skip rate)

- 1/1x, 1/2x, ………. 1/999x record speed

- ex: 1/2x ) R->S->R->S…- ex: 1/3x ) R->S->S->R->S->S->R…

- ex: 1/4x ) R->S->S->S->R->S->S… ( R : RECORD S : SKIP )

- ex : If record resolution is set at 360x240, 1/1x = 120 ips, 1/2x = 60 ips, 1/3x = 40 ips, etc.

26

Image 27
Contents 4Channel Built in DVR Installation & Safeguards Environment Condition for InstallationBefore You Start Contents FAQ Chap Chap Features & Package Contents Package Contents Search ③ Setup MenuStop PlayEthernet ④ ⑥Installation Configuration CHAP.3 InstallationDetailed Installation Connector cover bracket Power CameraMonitor Other External Device VCR, Video PrinterRS-232C ASCII-code Connector Pin Assignment DescriptionSystem Log-In System Menu Configuration Password SetupFactory Default Factory DefaultLive View Setup Display ConfigurationInterval Setup ※ While entered in the Menu Search Search Search BARTIME/DATE Event List PAN/TILT/ZOOM Camera Operation CD-R SetupRight Entering into the MenuDown LeftScreen Display Display SetupMonitor Setup Display SetupHDD Management ConfigurationCamera Setup TIME/DATE SetupNon-highlighted Area Motion SetupCamera Active Setup Motion Configuration Motion Detection AreaAlarm Setup Interval SetupAlarm Setup Interval SetupBuzzer Setup Password SetupSystem Information Super Fine Record SetupRecord Configuration MultiplexSchedule REC Setup Schedule SetupSchedule Setup Holiday SetupBACK-UP TCP/IP SetupIP Config Setup IP Config SetupConnection Setup RS-232C SetupPAN/TILT Setup Factory Default Language SetupFactory Default PC’s TCP/IP Setting DVR Network ConfigurationLocally Accessing the DVR using the Remote Software for Case aISP Accessing the DVR using the Remote Software for Case BRemotely Case B Single Static IP Directly Connected to the DVRCase C Dynamic or PPPoE IP w/Personal Router Case D Multiple Static IPs w/Personal Router Accessing the DVR using the Remote Software for Case CAccessing the DVR using the Remote Software for Case D Accessing the DVR using the Remote Software for Case E Setting, Playback, and Sequence buttons Remote Viewer programMain Interface Setting Screen Playback Interface through Remote Viewer Chap Network Setup Chap Network Setup Back-up CD Player Function buttonScreen division 1/4/9/16 Image Edit How do I Ping an IP address ? How do I choose a unique IP that matches my network?How do I open an MS-DOS or Command Prompt ? How do I forward a port in my router? Why is my remote video jerky?Specification of DVR Chap SpecificationsSpecification of Monitor Memo Best Picture Quality JPEG2000