Philips TH-37PR10U PC Input Terminals connection, Signal Names for Mini D-sub 15P Connector

Page 10

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

AUDIO

PC IN

Mini D-sub 15p

RGB

PC cable

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 768 × 720 dots (TH-37PR10U), 768 × 768 dots (TH-42PR10U) when the aspect mode is set to “NORMAL”, and 1,024 × 720 dots (TH-37PR10U), 1,024 × 768 dots (TH-42PR10U) when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

•The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

•Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector.

•Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when component connection) or “RGB” (when RGB signal connection). (see page 32)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10		9	8	7	6
15	14	13	12		11

Pin Layout for PC Input Terminal

Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
1	R (PR/CR)	6	GND (Ground)	11	NC (not connected)
2	G (Y)	7	GND (Ground)	12	SDA
3	B (PB/CB)	8	GND (Ground)	13	HD/SYNC
4	NC (not connected)	9	NC (not connected)	14	VD
5	GND (Ground)	10	GND (Ground)	15	SCL

10

Image 10

Contents English Español Operating Instructions Manual de instruccionesModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits Safety Precautions When using the Plasma DisplayAC Power Supply Cord MaintenanceSetup If problems occur during useAccessories Supplied AccessoriesCheck that you have the Accessories and items shown Connections AC cord fixingSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionCommunication parameters CommandSerial Terminals connection Basic format for control dataConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Selecting the On-Screen Menu Language Selecting the input signalInitial selections INPUT1 INPUT2 INPUT3 PCBasic Controls On OFFOFF Timer button Channel AdjustmentVolume Adjustment Digital Zoom see Press to accessOn-Screen Menu Displays Advanced SettingsSound POS. /SIZE Time / Power OFF Time On Time / Power OFFNormal Full During Multi PIP OperationsPicture Explanation Clock Phase Adjusting POS. /SIZEClock Phase RGB/PC in modeMulti PIP Sub screen Main screen Advanced PIPOne screen Advanced PIP Press to exit from Options menu 1366x768@60Hz RGB, DVI, HdmiDynamic Picture AdjustmentsStandard CinemaAdvanced Settings Sound Adjustment MutePosition Digital ZoomDisplay the operation guide Select the magnification required for the enlarged displayPress to set up DAY or Present Time of DAY Present Time SetupPresent Time Setup Button ForwardDisplay the SET UP Timer Screen Press to select SET UP TimerPower on Time / Power OFF Time Screensaver For preventing image retention Mode selectionStart setting Negative / Scroll selectionSetup of Screensaver Time Reduces screen image retentionOFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Customizing the Input labels Reduces power consumptionAddition sign Selected Input 3D Y/C Filter For Ntsc AV images SET UP for Input SignalsComponent / RGB in Select Component RGBPulldown / Video NR Color System / Panasonic AutoColor System Refresh Rate Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzOptions Adjustments Becomes the same as the Maximum VOL level Off Initial VOL Sets normal volume LevelVolume display can go up to 63 regardless of the settings Off MENU&ENTER OnFunction EnableInitial Power Normal StandbyNormalization State regardless of the slot power setting InstallationRotate Off Does not rotate the image Weekly Command Timer Time Set the time to execute a command program Press to select a command numberPress to select Time / Command Press to set each itemShipping condition Symptoms Check TroubleshootingSymptoms Checks Plasma Display panelPC input signals RGBCommand list of Weekly Command Timer Specifications Limits and Exclusions Limited Warranty Statement Panasonic Canada IncExecutive Office Customer’s RecordPanasonic Professional Display Company Panasonic Canada Inc