Philips 9P6440C1, 9P6040C1 manual Setting the Remote to Work Other Devices Search, Search Method

Page 44

SETTING THE REMOTE TO WORK OTHER DEVICES - SEARCH

SEARCH METHOD

Your TV remote can be set to work various accessory

SATELLITE RECEIVER

devices (VCRs, Cable Converters, Satellite Receivers) by what is called the SEARCH method.

Note: The Search Method only works with devices equipped with

Channel Display Indicators or capability. If the "Direct Access" code number method (shown in the previous section) did not set your remote to work your accessory device, then follow the easy steps listed below.

BEGIN

1Turn ON the desired device. Press the correct VCR or ACC system button on the remote.

2 Stand at least six feet away

from the front of the accessory

device. Point the remote toward

the unit. HOLD DOWN the

SURF and the desired System

(VCR or ACC) buttons at the

same time. KEEP HOLDING

1

VCR

 

 

06

 

07

09

CABLE TV

06

0708

CONVERTER

0809

06

 

070809

 

Don't let the Accessory Device scan up more than five channels

(in Search mode).

Six Feet

 

 

(minimum)

3

BUTTONS DOWN.

3Watch the Channel Indicator on the unit. Channel Numbers will SCAN UP when the unit has been identified. This may take up to two minutes.

4Release the SURF and System (VCR or ACC) buttons as soon as channel numbers start to scan up. The code has been identified and the remote is ready to operate with the accessory device.

STOP

SMART HELP

Remember, a minute or two

can seem very long, but the code should be located within two minutes.

Don't let the accessory device scan up more than five channels. The remote may pass up the right code and another two minute search cycle will have to be repeated.

If no channel change happens within two minutes, repeat steps 1-4. Should a channel change still not occur, the remote will not work with the desired unit.

REC•

 

PLAY

STATUS

 

 

CLEAR

 

 

 

 

 

 

REW

 

MENU

 

 

 

M

+

FF

 

 

◀◀

 

 

 

 

 

 

▶▶

 

 

 

 

 

 

PAUSE II

 

 

MUTE

 

STOP

SURF

 

 

VOL

 

 

 

CH

2

 

ON/OFF

POS

SWAP

FREEZE

4

 

 

 

 

SIZE

 

 

2 TUNER PIP

1

2

3

 

 

AB

 

 

 

TV/VCR 4 5 6

ENTER

SLEEP 7 8 9

SMART0

POWER VCR ACC TV

M O D E

2 4

44

Image 44
Contents Projection Television Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Standard TV broadcast VHF/UHF or Cable TVSHARPNESS, TINT, Picture Picture Menu Control AdjustmentsCOLOR, Brightness Picture Menu Controls Select Clearview controlRED/BLUE Convergence Select Convergence controlFlesh Correction Select FleshCorrection control Press the Menu buttonsFeature Menu Control Adjustments Picture SourceSelect Picture Source Select control Press the Menu buttons to move the RED highlight. PressFeature Menu Controls Closed CaptionSelect Closed Captioning control Text 1, 2, 3Cable Tuning Select Cable Channel Tuning controlCABLE- If you do have Cable TV connected to the TV. Channels 1-125 availableChannel Memory AUTO-PROGRAMMING Select Channel MemoryPress the Menu button to turn Press the Status or Menu MADD/DELETE Channels Select Channel Memory ADD/DELETE Channels controlPress the remotes number SET ClockSelect SET Clock control SET Alarm Timer Select SET Alarm Timer controlSleep Timer Press the Sleep button onPress the Sleep button Press the Status or MenuChannel Display Select Channel Display controlHalf Hour Reminder Select Half Hour Reminder controlSetup Code Number Parental ControlFirst lets set your Parental Code Select the ParentalParental Control Channel Blocking Select the Block Channels controlSelect the Channel Blocking itemContent Advisory Select the ContentPress theMENU button to Enter the correct ParentalContent Advisory Movie Ratings Select the Movie Ratings Menu optionSelect the desired Movie Blocking levelContent Advisory Parental Guidelines Select the Parental Guidelines Menu optionContent Advisory Blocking Options Review SettingsSelect the Blocking Options Menu controlSelect either Channel LabelsDo you ever have trouble remembering on which Display control LanguageSelect the Language Sound Menu Control Adjustments BASS, TREBLE, BalanceSelect BASS, or TREBLE, or Press the Status button toSound Menu Controls StereoSelect Stereo sound control Second Audio ProgramIncredible Stereo Select Incredible StereoPress the Menu Menu M buttons to highlightPress the Menu Menu M buttons to highlight Display VolumeSelect Display Volume TV Speakers Back of TVVariable Audio Output Jacks RED/WHITE Audio SystemSurround Sound Connect both externalPlace the speakers so Connect the Right and LeftUsing the AUDIO/VIDEO Input Jacks AUX 1 Video InputsConnect the Video OUT jack from the VCR to the AUX Connect the Audio OUT jacks Right and Left fromSide Video Inputs Press Play to view the tape onPicture and Sound from Playback Camcorder Tape AUDIO/VIDEO Output Jacks On CamcorderAUX1 S-VIDEO Inputs Picture and Sound from Playback of S-VHS VCR TapeVideo Cable Video OUT VHS VCRComponent Video Inputs Component Video Inputs provide for the highestDVD player to the AUX 1 Audio in jacks on the TV Select the AUX 1 Y P B P RAUDIO/VIDEO Outputs Connect the Video OUT jackConnect the Audio OUT Select the Antenna a Picture Source control onRemote Control Operation Smart PictureSmart Picture Change LabelSmart Sound Are you tired of the sound of commercials following youChannel SURF/SMART Surf Setting the TV Remote to Work Accessory Devices Direct Access Method Setting the Remote to Work Other Devices Search Your TV remote can be set to work various accessorySearch Method Device. Point the remote towardRemote Control Direct Entry Codes for Accessory Devices VCR Brand Remote Code noDVD Brand Remote Code no Using the Remotes VCR Buttons Rewind ButtonHOW to USE the PICTURE-IN-PICTURE PIP Feature Select control to ANT B Turn the TV onPlace the TVs PIP Source PIP on / OFF PIP Position PIP Swap PIP Freeze Using PIP with the Remote ControlPress the PIP ON/OFF button to show the PIP picture Select PIP Source control Selecting the Picture Source for PIPPIP Source Adjusting Picture -IN -PICTURE Color and Tint PIP Color / PIP TintSelect PIP Color or PIP Press the + and buttons toFirst use an optional signal Signal SplitterMore PIP Connections Audio Video CablesTV Help Menu He on screen Help menu offers both Operating TipsSelect Help on the TVs Main Menu Press the remotes Menu Follow the on Screen Directions to View Operating TipsTV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms Index Philips Consumer Electronics Company Texas Limited Warranty