Philips CCA092AT owner manual Timer Recording cont’d

Page 33

Timer Recording (cont’d) 33

4

Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not been stored yet).

NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds. Then information about the program in that position will appear on the screen. If this happens, press the STATUS/EXIT but- ton. Then use the Number buttons to select another position.

5

Use the Number buttons to enter the channel of the TV program you want to record.

●If you are recording from line input, press 0, 0. A/V IN will appear on the screen.

●If you are recording using a Cable Box, enter the Cable Box output channel (03 or 04). Be sure to select the channel of the TV program at the Cable Box and leave the Cable Box on for the timer recording.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL – – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

6

Press two Number buttons for the hour(s) you want the recording to begin. Press two Number buttons for the minute(s) you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

7

Follow the instructions in step 6 to set the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	09:30 PM
TIME OFF	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

Instructions continue on page 34.

4-7

POWERSLEEP

	PLAY
REW		F.FWD
	STOP
MENU	STATUS/EXIT	CLEAR

1	2	3
4	5	6	CH.
4	5	6
7	8	9
	0	ALT. CH	VOL.
	0	ALT. CH
SPEED	MEMORY	PAUSE/STILL
REC/OTR	TRACKING		MUTE

Helpful Hints

•If the numbers entered do not match the TV/VCR’s calendar, the entry will be rejected and a question mark will appear on the screen.

•To make corrections while you are programming a timer recording, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the cor-

rect information.

Image 33

Contents CCA092AT For Customer Use Dear Philips Magnavox product ownerSafety Precautions FeaturesIntroduction Philips Consumer Electronics Company recommends that youTable of Contents Using the Remote Control Putting Batteries in the Remote ControlTV/VCR Maintenance Erasure PreventionHooking Up the TV/VCR Hook up your TV/VCR using one of the connections shownRod Antenna supplied Crooked PinStraight Pin Hooking Up the TV/VCR cont’d Car battery cordMobile Connections To Cigarette LighterTurning On the TV/VCR You cannot set up channels if you are using a Cable BoxPress the Menu button Language SelectionAutomatic Channel Setup Press the PLAY/ o button or the STOP/ p button to select Adding/Deleting ChannelsManual Clock Setting Instructions continue onCable Box users must set the clock manually Setting the Clock cont’d Automatic PBS Channel Selection Setting the Clock cont’dWait for the TV/VCR to find the time Manual PBS Channel Selection Press the PLAY/ button or the STOP/ button to Select SET PBS CH. MANUAL. Then, press the F.FWD/BUse the Number buttons to select your PBS station Daylight-Savings Time Time Zone Primary SetupFront Panel ANTenna Jack Rear PanelDC 13.2V Jack AC 120V JackRemote Control Buttons Remote Control Buttons cont’d If you select Status ON, then select Counter only OFF If you select Status ON, then select Counter only onIf you select Status OFF Adjusting the Picture Controls Decrease Increase Adjusting the Picture Controls cont’dMore brilliant SofterPlaying Recording options are on pages RecordingOne-Touch Recording Different brands of equipment may operate differently Rerecording Tape DuplicationDaily Timer RecordingTimer Recording cont’d Timer Recording cont’d With the TV/VCR on, press the Menu button Checking or Clearing Timer RecordingsPress the PLAY/ button or the STOP/ button to select VCR PROGRAM, then press the F.FWD/B buttonDefeat Recording Repeat Play Insert a tape in the TV/VCR Press the Menu button B Repeat PlayPress the STATUS/EXIT button to remove the display. a Repeat Play cont’dPress the STATUS/EXIT button. The real-time counter will Real-Time Counter MemoryForward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still PictureGround Blue BackgroundSleep Timer Volume Bar Reminder Automatic Operation Features Glossary SpecificationsHelpful Hints Helpful Hints cont’d TV/VCR Combination Limited WarrantyControls Remote 23-24 Tv/vcr IndexSupplied Accessories