Philips CCA092AT Turning On the TV/VCR, You cannot set up channels if you are using a Cable Box

Page 9

Before you turn on the TV/VCR, make sure batteries are in the remote control and the TV/VCR is hooked up correctly.

The instructions on this page work only when you turn on the TV/VCR for the first time.

1

Press the POWER button. The TV/VCR will come on and the screen shown below will appear.

SELECT LANGUAGE

> ENGLISH

ON

ESPAÑOL

SELECT KL OR

PRESS MENU TO CONTINUE

2

Press the PLAY/K button or the STOP/L button to select

English or Spanish on-screen displays and menus.

3

Press the MENU button. The screen shown below will appear.

CONNECT ANTENNA OR CABLE

TO TVCR

THEN PRESS B

TO END PRESS EXIT

Turning On the TV/VCR 9

1

POWER

 

 

 

SLEEP

 

2

 

PLAY

 

 

4

REW

STOP

 

F.FWD

3

MENU

STATUS/EXIT

CLEAR

 

1

2

 

3

 

 

 

4

5

 

6

CH.

 

5

 

 

 

7

8

 

9

 

 

 

0

ALT. CH

VOL.

 

 

 

 

SPEED MEMORY

PAUSE/STILL

 

 

REC/OTR

TRACKING

 

MUTE

 

4

Press the F.FWD/B button to begin automatic channel setup. The TV/VCR will memorize all available channels. When channels are set, CHANNELS ARE SET will appear on the screen briefly. Then the TV/VCR will go to the lowest channel pro- grammed.

(If you try to set up channels when there is no antenna or cable connected to the TV/VCR, programming will appear to take place, but eventually a NO TV SIGNALS ... message will appear on the screen. Connect an antenna or cable to the ANT(enna) jack on the TV/VCR, then press the F.FWD/B button again. You may need to follow the steps on page 11 instead.)

5

Use the CH(annel) m/n button or the Number buttons on the remote control to select a TV/VCR channel. Use the VOL(ume) m/nbutton to adjust the sound.

Helpful Hints

If you do not see any on-screen dis- plays when you turn on the TV/VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps on pages 10-11 to select a language and set up channels.

To skip step 2, press the MENU button. All on-screen displays will be in English. To skip step 4, press the STATUS/EXIT button. Channels will not be set up, and CHANNELS NOT SET will appear on the screen briefly.

You cannot set up channels if you are using a Cable Box.

Line Input mode will always be stored in the TV/VCR’s memory as channel 00. When you select chan- nel 00, A/V IN will appear on the screen briefly. Press the CH(annel) m/n button or the Number but- tons to select another channel.

Image 9
Contents CCA092AT For Customer Use Dear Philips Magnavox product ownerSafety Precautions FeaturesIntroduction Philips Consumer Electronics Company recommends that youTable of Contents Using the Remote Control Putting Batteries in the Remote ControlTV/VCR Maintenance Erasure PreventionHooking Up the TV/VCR Hook up your TV/VCR using one of the connections shownRod Antenna supplied Crooked PinStraight Pin Hooking Up the TV/VCR cont’d Car battery cordMobile Connections To Cigarette LighterTurning On the TV/VCR You cannot set up channels if you are using a Cable BoxPress the Menu button Language SelectionAutomatic Channel Setup Press the PLAY/ o button or the STOP/ p button to select Adding/Deleting ChannelsManual Clock Setting Instructions continue onCable Box users must set the clock manually Setting the Clock cont’d Automatic PBS Channel Selection Setting the Clock cont’dWait for the TV/VCR to find the time Manual PBS Channel Selection Press the PLAY/ button or the STOP/ button to Select SET PBS CH. MANUAL. Then, press the F.FWD/BUse the Number buttons to select your PBS station Daylight-Savings Time Time Zone Primary SetupFront Panel ANTenna Jack Rear PanelDC 13.2V Jack AC 120V JackRemote Control Buttons Remote Control Buttons cont’d If you select Status ON, then select Counter only OFF If you select Status ON, then select Counter only onIf you select Status OFF Adjusting the Picture Controls Decrease Increase Adjusting the Picture Controls cont’dMore brilliant SofterPlaying Recording options are on pages RecordingOne-Touch Recording Different brands of equipment may operate differently Rerecording Tape DuplicationDaily Timer RecordingTimer Recording cont’d Timer Recording cont’d With the TV/VCR on, press the Menu button Checking or Clearing Timer RecordingsPress the PLAY/ button or the STOP/ button to select VCR PROGRAM, then press the F.FWD/B buttonDefeat Recording Repeat Play Insert a tape in the TV/VCR Press the Menu button B Repeat PlayPress the STATUS/EXIT button to remove the display. a Repeat Play cont’dPress the STATUS/EXIT button. The real-time counter will Real-Time Counter MemoryForward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still PictureGround Blue BackgroundSleep Timer Volume Bar Reminder Automatic Operation Features Glossary SpecificationsHelpful Hints Helpful Hints cont’d TV/VCR Combination Limited WarrantyControls Remote 23-24 Tv/vcr IndexSupplied Accessories