50 SmartLock (cont’d)
To change the access code, follow these steps.
1
Press the COMBI button, then press the MENU button.
> SMARTLOCK | | PRESS B |
| REVIEW | | |
| EXIT | | |
| PRIM. SETUP | | |
| VCR PROGRAM | | |
| VCR SETUP | | |
2,4
POWER | | EJECT |
SLEEP/WAKE UP | SPEED | MEMORY |
REC/OTR | | PAUSE/STILL |
PLAY
REWF.FWD
2
Press the PLAY/▲ button or the STOP/▼ button to select SMARTLOCK. Then, press the F.FWD/B button.
SMARTLOCK
![](/images/new-backgrounds/1231707/23170799xi2.webp)
_
_ _ _
Enter Your Access Code
3
STOP
1 2 3
4 5 6
7 8 9
FM 0 SURF
CABLE/DBS COMBI
VCR PLUS+
VAR.SLOW/ENTER
TRACKINGF.ADV
Use the Number buttons to enter your old access code. The default code is 0711. If you have never set up your personal access code, use 0711 now.
After you enter the code, the SMARTLOCK menu will appear.
SMARTLOCK
X X X
-![](/images/new-backgrounds/1231707/23170799xi6.webp)
![](/images/new-backgrounds/1231707/23170799xi7.webp)
Enter Your Access Code
4
Press the PLAY/▲ button or the STOP/▼ button to select CHANGE CODE. Then, press the F.FWD/B button.
SMARTLOCK
BLOCK
>CHANGE CODE
SELECT KL CHOOSE B
TO END PRESS EXIT
5
Use the Number buttons to enter your desired access code in the New Code space. Then, enter the same code in the Confirm Code space.
Your new access code should be recorded. You will return to the SMARTLOCK menu.
New Code | | _ | _ _ _ |
| | |
| | |
Confirm Code | _ | _ _ _ |
6
SMART
SKIP INDEX
PICTURE SOUND SEARCH SEARCH
3,5
Helpful Hints
•In order to protect the privacy of the access code, an X will appear on the screen instead of the num- ber you enter.
•If a “Wrong Code...” message appears on the screen after you complete step 5, you entered the wrong numbers in the Confirm Code space. Repeat the steps on this page.
•You cannot use the default code after you set up your personal access code.
•If a power failure occurs, the default code, 0711, will be the active access code again.
•If you connect the power cord to an AC outlet that is controlled by a wall switch, your personal access code will be erased every time you turn off the power at the wall switch. The default code will be the active code again.
Press the STATUS/EXIT button.
CCB134AT CCB194AT
This bolt of lightning indi- cates uninsulated material
Dear Philips product owner
For Customer Use
Model No Serial No
Introduction
Features
Safety Precautions
Declaration of Conformity
Table of Contents
TV/VCR Maintenance
Putting Batteries in the Remote Control
Using the Remote Control
Erasure Prevention
Rod Antenna
Hook up your TV/VCR using one of the connections shown
Hooking Up the TV/VCR
Bent pin
Hooking Up the TV/VCR cont’d
AUDIO/VIDEO Jacks on front
Crooked Pin Straight Pin
Press the Menu button. The screen shown below will appear
Press the Combi button, then press the Power button
Turning On the TV/VCR
Language Selection
Press the Combi button, then press the Menu button
Automatic Channel Setup
Wait for the TV/VCR to set up channels
Repeat steps 3-4 to add or delete other channels
Adding/Deleting Channels
Press the PLAY/o button or the STOP/p button to select
Programming of the last channel you selected will appear
Cable Box users must set the clock manually
Setting the Clock
Manual Clock Setting
Setting the Clock cont’d
Setting the Clock cont’d
Automatic PBS Channel Selection
NOW Searching flashes on the TV/VCR screen
Wait for the TV/VCR to find
Time
Manual PBS Channel Selection
Use the Number buttons to select your PBS station
Wait for the TV/VCR to find the time
Daylight-Savings Time
Time Daylight Savings Time
Press the PLAY/ button or the STOP/ button to select
PRIM. SETUP. Then, press the F.FWD/B button
Time Zone
Within 30 seconds, press the CABLE/DBS button
Setting the Remote to Operate a Cable Box/DBS
Press the Mute button
Setting the Remote to Operate a Cable Box/DBS cont’d
Power Button
Earphone Jack Volume o/ p Buttons
Wireless Remote Sensor
Cassette Compartment
ANTenna Jack
AC Power Cord
Rear Panel
Connect your antenna or cable here
Remote Control Buttons
Memory Button
VOLume m/ n Button
PAUSE/STILL Button
REWind/ Button
When you finish, press the STATUS/EXIT button
Adjusting the Picture Controls
Adjust the picture control. Refer to the chart on
Press the REWind/ button or the F.FWD/B button to
Decrease Increase
Decreased brightness
If you select Status ON, then select Counter only on
On-Screen Status Displays
If you select Status ON, then select Counter only OFF
If you select Status OFF
Playing
Insert a tape in the TV/VCR
Press the RECord/OTR button once to start recording
Power button to turn on the TV/VCR, if necessary
Recording
One-Touch Recording
OTR
Rerecording Tape Duplication
Different brands of equipment may operate differently
Defeat Recording
Follow the steps below to prevent accidental recording
Daily
Timer Recording
Lowed by the SET Clock menu
Timer Recording cont’d
Timer Recording cont’d
FM 0 Surf VOL
Checking or Clearing Timer Recordings
Station
Setting Up the VCR Plus+ Programming System
TV Channels
Setting Up the VCR Plus+ Programming System cont’d
Timer Recording With the VCR Plus+ Programming System
You have completed the steps on pages
Timer Recording With the VCR Plus+ Programming System cont’d
Real-Time Counter Memory
Appear on the screen
ON-SCREEN Mode Defeat Recording OFF
Repeat Play
B Repeat Play
Insert a tape in the TV/VCR
Repeat Play cont’d
Flashing a will become a flashing B
Super High Speed Searching LP/SLP
Playback Options
Forward and Reverse Searching SP/LP/SLP
Viewing a Still Picture
Blue Background
SmartLock
To block ratings, follow the steps below
Example Specific Sub-ratings
SmartLock cont’d
Ratings are defined on
To change the access code, follow these steps
After you enter the code, the Smartlock menu will appear
To check the SmartLock settings, follow these steps
TV-Y7
Press the Combi button, then press the SLEEP/WAKE UP button
Sleep Timer
Timer during a recording
Wake Up Timer
Menu
Closed Caption
Example
Screen
Half-screen text
Closed Caption cont’d
Standard Closed Captions
Volume will stay at the same level
Volume Bar/Smart Sound
Volume Bar
Smart Sound
Automatic Operation Features
FM Radio
SmartPicture/FM Radio
SmartPicture
Follow the steps below to listen to FM radio stations
If another remote control beeps
Press the Mute button, then press the PAUSE/STILL button
Reminder
Press the Combi button, then press the Menu button
Index Search
Specifications
Glossary
Helpful Hints
Helpful Hints cont’d
Model # Serial #
Limited Warranty
Please contact Philips at French Speaking English Speaking
Index
Supplied Accessories