Philips CCB 194AT, CCB 134AT owner manual If another remote control beeps

Page 59

Your TV/VCR can find your remote control for you.

When you press the POWER button on the TV/VCR to turn on the TV/VCR, your remote control beeps and LOCATING REMOTE appears on the screen. The remote control will beep for about 30 seconds. Or, press any button on the remote control to stop the beeping.

If another remote control beeps...

The TV/VCR may find other remote controls. If this occurs, you can program the TV/VCR to find only its remote control. Follow the steps below.

1

Press the COMBI button, then press the MENU button.

2

Press the PLAY/button or the STOP/button to select PRIM. SETUP, then press the F.FWD/B button.

3

Press the PLAY/button or the STOP/button to select REMOTE LOCATOR, then press the F.FWD/B button.

PRESS MUTE THEN

PAUSE KEY

TO CHANGE CODE FROM 4

TO END PRESS EXIT

4

Press the MUTE button, then press the PAUSE/STILL button.

YOUR REMOTE LOCATOR

CODE IS 4

PRESS ANY DIGIT

TO CHANGE CODE

TO END PRESS EXIT

5

Press one Number button (0 - 9) to enter a single-digit code for your remote control. Your remote control will beep briefly.

YOUR REMOTE LOCATOR

CODE HAS BEEN CHANGED

NEW CODE IS 3

TO END PRESS EXIT

6

Press the STATUS/EXIT button.

Remote Locator 59

If another remote control beeps ...

 

 

2-3

 

 

POWER

 

 

EJECT

 

 

SLEEP/WAKE UP

SPEED

MEMORY

 

6

REC/OTR

 

 

 

PAUSE/STILL

 

 

 

PLAY

 

 

REW

STOP

F.FWD

 

1

MENU

STATUS/EXIT

CLEAR

 

1

2

 

3

 

 

 

4

5

 

6

CH.

 

 

 

 

 

 

7

8

 

9

 

 

 

FM

0

 

SURF

VOL.

 

 

 

 

 

 

 

 

CABLE/DBS

COMBI

 

 

4

 

 

 

VCR PLUS+

 

 

VAR.SLOW

 

/ENTER

MUTE

 

TRACKING

 

F.ADV

SLOW

 

SMART

SKIP

INDEX

 

 

PICTURE

SOUND

SEARCH SEARCH

 

5

 

 

 

 

 

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two condi- tions: (1) This device may not cause harmful interference, and (2) this device must accept any inter- ference received, including inter- ference that may cause undesired operation.

Helpful Hint

The volume will be delayed while the LOCATING REMOTE message appears on the screen. Press the STATUS/EXIT button to remove the message and restore the volume.

Image 59
Contents CCB134AT CCB194AT Model No Serial No Dear Philips product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents Erasure Prevention Putting Batteries in the Remote ControlUsing the Remote Control TV/VCR MaintenanceRod Antenna Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR Crooked Pin Straight Pin Hooking Up the TV/VCR cont’dAUDIO/VIDEO Jacks on front Bent pinPress the Menu button. The screen shown below will appear Press the Combi button, then press the Power buttonTurning On the TV/VCR Press the Combi button, then press the Menu button Language SelectionWait for the TV/VCR to set up channels Automatic Channel SetupProgramming of the last channel you selected will appear Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Repeat steps 3-4 to add or delete other channelsCable Box users must set the clock manually Setting the ClockManual Clock Setting Setting the Clock cont’d Automatic PBS Channel Selection Setting the Clock cont’dNOW Searching flashes on the TV/VCR screen Wait for the TV/VCR to findTime Manual PBS Channel Selection Wait for the TV/VCR to find the time Use the Number buttons to select your PBS stationTime Daylight Savings Time Daylight-Savings TimePress the PLAY/ button or the STOP/ button to select PRIM. SETUP. Then, press the F.FWD/B buttonTime Zone Within 30 seconds, press the CABLE/DBS button Setting the Remote to Operate a Cable Box/DBSPress the Mute button Setting the Remote to Operate a Cable Box/DBS cont’d Cassette Compartment Earphone Jack Volume o/ p ButtonsWireless Remote Sensor Power ButtonConnect your antenna or cable here AC Power CordRear Panel ANTenna JackRemote Control Buttons REWind/ Button VOLume m/ n ButtonPAUSE/STILL Button Memory ButtonPress the REWind/ button or the F.FWD/B button to Adjusting the Picture ControlsAdjust the picture control. Refer to the chart on When you finish, press the STATUS/EXIT buttonDecreased brightness Decrease IncreaseIf you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status ON, then select Counter only onInsert a tape in the TV/VCR PlayingPress the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording OTR One-Touch RecordingDifferent brands of equipment may operate differently Rerecording Tape DuplicationFollow the steps below to prevent accidental recording Defeat RecordingDaily Timer RecordingLowed by the SET Clock menu Timer Recording cont’d FM 0 Surf VOL Timer Recording cont’dChecking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels Setting Up the VCR Plus+ Programming System cont’d You have completed the steps on pages Timer Recording With the VCR Plus+ Programming SystemTimer Recording With the VCR Plus+ Programming System cont’d Appear on the screen Real-Time Counter MemoryRepeat Play ON-SCREEN Mode Defeat Recording OFFInsert a tape in the TV/VCR B Repeat PlayFlashing a will become a flashing B Repeat Play cont’dViewing a Still Picture Playback OptionsForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPBlue Background To block ratings, follow the steps below SmartLockExample Specific Sub-ratings SmartLock cont’dRatings are defined on After you enter the code, the Smartlock menu will appear To change the access code, follow these stepsTV-Y7 To check the SmartLock settings, follow these stepsPress the Combi button, then press the SLEEP/WAKE UP button Sleep TimerTimer during a recording Wake Up Timer Screen Closed CaptionExample MenuHalf-screen text Closed Caption cont’dStandard Closed Captions Smart Sound Volume Bar/Smart SoundVolume Bar Volume will stay at the same levelAutomatic Operation Features Follow the steps below to listen to FM radio stations SmartPicture/FM RadioSmartPicture FM RadioPress the Mute button, then press the PAUSE/STILL button If another remote control beepsPress the Combi button, then press the Menu button ReminderIndex Search Specifications Glossary Helpful Hints Helpful Hints cont’d Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Supplied Accessories