Philips SVA102 owner manual Turning on Your VCR, 2Turn on the TV

Page 11

Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected (see pages five-10).

You can not set up channels if you are using a Cable Box/DBS.

The instructions on this page only work when you turn on the VCR for the first time. If there is a power failure or if the VCR is unplugged for more than one minute, you may need to repeat the instructions on this page.

1

Press the POWER button. The POWER light and the VCR/TV light will appear.

2

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR. The menu shown

below will appear.

LANGUAGE SELECT

 

ENGLISH

[ON]

ESPAÑOL

 

3

Press the PLAY button or the STOP button to select ENGLISH or ESPAÑOL. [ON] will appear beside your choice.

4

Press the F.FWD button or the MENU button. TUNER SET

UP will appear on the screen.

TUNER SET UP

5

Press the MENU button, the F.FWD button, or the REWIND button to begin automatic channel setup. TUNER SET UP will flash on the screen. When channels are set up, the TV will go to the lowest channel available.

The VCR will memorize all available channels, so when you use the CHANNEL o/p buttons, you’ll only scan through channels that you receive.

Turning on Your VCR 11

2Turn on the TV.

1

POWER

VCR/TV

EJECT

1 2 3

4 5 6

7 8 9 CHANNEL

 

 

0

 

+100

 

 

 

SPEED

RENTAL

 

AUTO

CLOCK/

 

 

SELECTOR

REPEAT

COUNTER

4

 

 

5

MENU DISPLAY

EXIT

COUNTER

 

 

 

RESET

MEMORY

REWIND

 

/ PLAY

F.FWD

 

RECORD

 

/ STOP

PAUSE/STILL

 

3

Helpful Hints

If you do not see any on-screen dis- plays when you turn on the VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps under “Automatic Channel Setup” on page 12 and “Language Selection” on page 16.

If you try to set up channels when there is no antenna or cable connect- ed to the VCR, programming will appear to take place. Eventually, TUNER SET UP will appear on the screen steadily, and channel program- ming will stop. Connect an antenna or cable to the ANT(enna) IN jack of the VCR, then press the MENU but- ton, the F.FWD button, or the REWIND button again. Channel pro- gramming will begin again.

Image 11
Contents Video Cassette Recorder For Customer Use Warranty VerificationIntroduction FeaturesSafety Precautions Table of Contents Replace the battery compartment lid Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Select the channel you want to watch at the Cable Box/DBS Recording One Channel/Watching AnotherHookups With a Stereo TV 2Turn on the TV Turning on Your VCRAutomatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’dFollow the steps below to set your VCR’s clock. Make sure Setting the Clock96-7 Setting the Clock cont’dLanguage Selection Press the Counter RESET/EXIT buttonOn-Screen Status Displays OFF mode Press the Display button once Count modePress the Display button once Clock mode Rental Selector Button Remote Control ButtonsPower Button Number ButtonsCLOCK/COUNTER Button Counter RESET/EXIT ButtonEject Button Auto Repeat ButtonVCR Display Panel Front Panel Video OUT Jack AC Power CordRear Panel Audio OUT JackRead and follow the steps below to play a tape Playing1Turn on the TV Insert a tape RecordingStopping an OTR Starting an OTRProgram Number → Once Daily Weekly Timer RecordingRepeat the procedure in to set the recording’s end time Timer Recording cont’d4Press the Counter RESET/EXIT button to exit Correcting a Timer Recording Cancelling a Timer RecordingSelect Auto Return Auto ReturnPress the Play button or the Stop button repeatedly to To stop recording, press the Stop button Press the VCR/TV button on the VCR remote control toTo return to the channel being recorded, use the TV Put the VCR in VCR position. The VCR/TV light will appearRF coaxial cable Rerecording Tape DuplicationRepeat Play Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPRental Play Press the Play button to watch the tape Real-Time Counter MemoryAutomatic Playback Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel Channel 3 or GlossarySpecifications Video Cassette Recorder Limited WarrantyIndex Supplied Accessories