Philips SVA102 owner manual Recording One Channel/Watching Another

Page 9

Hookups With a Cable Box/Direct Broadcast System (cont’d) 9

With this connection:

You may watch one channel while recording another.

You may not record scrambled channels.

1 VCR

 

 

ANT

 

 

IN

OUT

IN

OUT

 

 

2

75V

 

ANT

/

 

CABLE

 

IN

 

 

OUT

 

Cable Box/DBS

VIDEO

Cable

Signal

CH3 CH4

 

RF coaxial

 

 

cable

 

RF coaxial

3

TV’s ANTENNA

IN Jack

cable

Connections

1

Connect a Cable signal to the VCR’s ANT(enna) IN Jack.

2

Use an RF coaxial cable (supplied) to connect the OUT Jack on the VCR to the IN Jack on the Cable Box/DBS.

3

Use a second RF coaxial cable to connect the OUT Jack on the Cable Box/DBS to the ANTENNA IN Jack on the TV.

Recording One Channel/Watching Another

1

Put the Cable Box/DBS on the same channel as the VCR’s CH3/CH4 switch. (Make sure the TV is on the Cable Box/DBS output channel, 03 or 04.)

Then, with the VCR in VCR position (the VCR/TV light will appear on the display panel), use the CHANNEL o/p buttons to select the channel you want to record at the VCR. Start the recording.

2

Press the VCR/TV button once to put the VCR in TV position. (The VCR/TV light will disappear.)

3

Select the channel you want to watch at the Cable Box/DBS.

Helpful Hint

When you play a tape, make sure the Cable Box/DBS is set to the same channel as the CH3/CH4 switch on the VCR. Set the TV to the Cable Box/DBS output channel (03 or 04).

Image 9
Contents Video Cassette Recorder For Customer Use Warranty VerificationFeatures Safety PrecautionsIntroduction Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Replace the battery compartment lidDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dHookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Select the channel you want to watch at the Cable Box/DBS Recording One Channel/Watching AnotherHookups With a Stereo TV 2Turn on the TV Turning on Your VCRAutomatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’dFollow the steps below to set your VCR’s clock. Make sure Setting the Clock96-7 Setting the Clock cont’dLanguage Selection Press the Counter RESET/EXIT buttonOFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Status Displays Power Button Remote Control ButtonsNumber Buttons Rental Selector ButtonEject Button Counter RESET/EXIT ButtonAuto Repeat Button CLOCK/COUNTER ButtonVCR Display Panel Front Panel Rear Panel AC Power CordAudio OUT Jack Video OUT JackRead and follow the steps below to play a tape Playing1Turn on the TV Insert a tape RecordingStopping an OTR Starting an OTRProgram Number → Once Daily Weekly Timer RecordingRepeat the procedure in to set the recording’s end time Timer Recording cont’d4Press the Counter RESET/EXIT button to exit Correcting a Timer Recording Cancelling a Timer RecordingAuto Return Press the Play button or the Stop button repeatedly toSelect Auto Return To return to the channel being recorded, use the TV Press the VCR/TV button on the VCR remote control toPut the VCR in VCR position. The VCR/TV light will appear To stop recording, press the Stop buttonRF coaxial cable Rerecording Tape DuplicationRepeat Play Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureRental Play Press the Play button to watch the tape Real-Time Counter MemoryAutomatic Playback Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel Channel 3 or GlossarySpecifications Video Cassette Recorder Limited WarrantyIndex Supplied Accessories