Philips SVA102 owner manual Auto Return, Press the Play button or the Stop button repeatedly to

Page 30

30 Auto Return

Follow the steps below to make the VCR rewind to the beginning of the programs after it has finished all timer recordings. Make sure:

●The VCR is on and is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.)

1

Press the MENU button repeatedly until the VCR SET UP menu appears.

VCR SET UP

→ AUTO REPEAT RENTAL AUTO RETURN

	2		1
	Press the PLAY button or the STOP button repeatedly to		1
	Press the PLAY button or the STOP button repeatedly to
	select AUTO RETURN.
	VCR SET UP
	AUTO REPEAT
	RENTAL
	→ AUTO RETURN
	3		2
	Press the F.FWD button so that [AUTO] appears next to
	AUTO RETURN on the screen.
	VCR SET UP
	AUTO REPEAT
	RENTAL
	→ AUTO RETURN	[AUTO]

POWER

VCR/TV

EJECT

1 2 3

4 5 6

7 8 9 CHANNEL

0 +100

RENTAL AUTO CLOCK/ SPEED SELECTOR REPEAT COUNTER

MENU DISPLAY EXIT COUNTER

	RESET	MEMORY
REWIND	/ PLAY	F.FWD
RECORD	/ STOP	PAUSE/STILL

4

3

4

Press the COUNTER RESET/EXIT button.

Remember to turn off the VCR before the timer recording. When all the timer recordings are completed, the TIMER light will flash and the VCR will rewind the tape to the beginning of the record- ed programs.

Helpful Hints

•If additional timer recordings are programmed to take place later, the Auto Return function will not operate until all the programs are recorded.

•To cancel this function, follow steps 1-2 above. At step 3, press the F.FWD button so that [AUTO] no longer appears beside AUTO RETURN. Press the COUNTER RESET/EXIT button.

Image 30

Contents Video Cassette Recorder Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Replace the battery compartment lidHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRHookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Recording One Channel/Watching Another Select the channel you want to watch at the Cable Box/DBSHookups With a Stereo TV Turning on Your VCR 2Turn on the TVAutomatic Channel Setup Automatic Channel Setup cont’d Adding/Deleting ChannelsSetting the Clock Follow the steps below to set your VCR’s clock. Make sureSetting the Clock cont’d 96-7Press the Counter RESET/EXIT button Language SelectionOFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Status Displays Number Buttons Remote Control ButtonsPower Button Rental Selector ButtonAuto Repeat Button Counter RESET/EXIT ButtonEject Button CLOCK/COUNTER ButtonVCR Display Panel Front Panel Audio OUT Jack AC Power CordRear Panel Video OUT JackPlaying Read and follow the steps below to play a tapeRecording 1Turn on the TV Insert a tapeStarting an OTR Stopping an OTRTimer Recording Program Number → Once Daily WeeklyTimer Recording cont’d Repeat the procedure in to set the recording’s end time4Press the Counter RESET/EXIT button to exit Cancelling a Timer Recording Correcting a Timer RecordingAuto Return Press the Play button or the Stop button repeatedly toSelect Auto Return Put the VCR in VCR position. The VCR/TV light will appear Press the VCR/TV button on the VCR remote control toTo return to the channel being recorded, use the TV To stop recording, press the Stop buttonRerecording Tape Duplication RF coaxial cableRepeat Play Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureRental Play Real-Time Counter Memory Press the Play button to watch the tapeAutomatic Playback Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel Channel 3 orSpecifications Limited Warranty Video Cassette RecorderIndex Supplied Accessories