Philips VRZ262AT owner manual Turning on Your VCR, 2Turn on the TV

Page 11

VRZ262(H1920).QX33 4/9/99 9:32 AM Page 11

Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected correctly.

●Follow the steps on this page only when you plug the VCR power cord into the wall outlet for the first time.

●You can not program channels if you are using a Cable Box or a Direct Broadcast System.

Turning on Your VCR 11

2Turn on the TV.

1

POWER

VCR

TV

CBL/DBS

1

Press the VCR button, then the POWER button. The VCR light and the PWR. (power) light will appear on the display panel.

2

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR. The display shown below will appear. (If the display does not appear, check your hookups, then follow the steps on page 12 to set up channels and page 17 to select a language.)

SELECT op

 

→ ENGLISH

ON

ESPAÑOL

 

MAKE SELECTION OR

PUSH MENU TO CONTINUE

3

Within 60 seconds, press the PLAY/o button or the STOP/p button to select English or Spanish on-screen displays.

3

4

 

 

VCR/TV

1

2

3

4

5

6

 

 

CHANNEL

7

8

9

VCR PLUS+

 

 

/ENTER

 

 

0+100

SPEED

TIME SEARCH

MUTE

VOLUME

 

PLAY

 

REW

 

F.FWD

 

STOP

 

REC/OTR

MEMORY

SLOW

PAUSE/STILL

MENU

STATUS/EXIT

CLEAR

EJECT

5

4

Press the MENU button. The display shown below will appear.

CONNECT ANTENNA OR CABLE

TO VCR

THEN . . .

PUSH CH UP KEY

OR . . .

FOR PLAY ONLY – PUSH STOP

5

Within 60 seconds, press the CHANNEL o button to begin automatic channel programming. AUTO SET PRO- CEEDING PLEASE WAIT will appear on-screen. The VCR will memorize all available channels. When all channels are pro- grammed, CHANNELS ARE SET will appear on-screen briefly, then TV programming will appear.

Now, when you press the CHANNEL o/p buttons, you’ll only scan through channels that you receive.

Helpful Hints

•To skip this feature and play a tape immediately, insert a tape with its record tab removed. Or, to skip step 3, press the MENU button. All on- screen displays will be in English. To skip step 5, press the STOP button. Channels will not be programmed, and CHANNELS NOT SET will appear on-screen.

•If you try to program channels when there is no antenna or cable connected to the VCR, programming will appear to take place, but even- tually a NO TV SIGNALS message will appear. Connect an antenna or cable to the VCR’s ANT(enna) IN Jack and try again. You may need to follow the steps on page 12.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents VRZ262AT For Customer Use Dear Philips Magnavox product ownerIntroduction FeaturesSafety Precautions Table of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemCH3 Plug in the TV and the VCRRecording/Viewing Any Channel ConnectionsRecording One Channel/Watching Another Hookups With a Cable Box / Direct Broadcast System cont’dHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single digit num- ber Setting the ClockDaylight-Saving Time Language Selection Setting the Remote to Operate a TV 2Find VCR PLUS+/ENTER Button Remote Control ButtonsRemote Control Buttons cont’d If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Playing VCR light does not appear, press the VCR/TV button once RecordingRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM See page 48 for more hints Checking or Cancelling Timer RecordingsChannels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Press the VCR PLUS+ /ENTER button Do each step within 60 seconds of the previous stepTimer Recording With the VCR Plus+ Programming System cont’d VCR Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayWithin 10 seconds, use the Number buttons to enter Time SearchPress the VCR button Press the Time Search button Real-Time Counter Memory Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound SystemPress the RECord/OTR button to start recording Multi-Channel Television Sound System cont’dPlease see additional notes on Hi-Fi Stereo Sound SystemPress the VCR button, then the Menu button Hi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Cable Box Output Channel 03 or GlossarySpecifications Video Cassette Recorder Limited WarrantyIndex VRZ262H1920.QX33 4/9/99 933 AM VRZ262H1920.QX33 4/9/99 933 AM Supplied Accessories
Top Page Image Contents