Philips VRZ262AT Multi-Channel Television Sound System, Understanding On-Screen Displays

Page 44

VRZ262(H1920).QX33 4/9/99 9:33 AM Page 44

44 Multi-Channel Television Sound System

Your VCR can play recordings broadcast in Hi-Fi (high fidelity) stereo, which produces a crisp, clear sound from two sources. Your VCR also can play tapes recorded in a second audio (usually, that means your program is recorded in a second language). Of course, your VCR will play tapes recorded in monaural (single-source) sound as well.

Your VCR also will record in Hi-Fi stereo or in second audio, so when you play back that tape on the VCR, it will be in stereo or second audio. If you play back the tape on a VCR that can’t play back tapes in stereo or second audio, the VCR will automatically play the tape in monaural sound.

Read the directions on this page to familiarize yourself with your VCR’s stereo and second audio setups. Then follow the directions on page 45 to record in stereo or second audio and the directions on pages 46- 47 to play back tapes recorded in Hi-Fi stereo.

Understanding On-Screen Displays

When you receive a signal from a channel you’re watching, portions of the on-screen display shown below will appear when you press the STATUS/EXIT button on the remote control.

The indication 2ND AUD or TV STEREO that appears on this side of the status display tells you if your VCR is programmed to receive a sec- ond audio or stereo broadcast (it can- not be programmed to receive both at the same time).

Specifically…

STOP

 

12:00 AM

TV STEREO

CH 02

 

 

STEREO

 

2ND AUD

SLP

1:23:45

HIFI

The indication 2ND AUD or STEREO that appears on this side of the status display tells you if the program you’re watching is available in second audio or stereo.

This indication is not available during tape playback.

STOP

 

 

 

12:00 AM

 

TV STEREO

CH 02

 

 

 

 

 

 

STEREO

 

 

 

 

 

2ND AUD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLP

1:23:45

HIFI

 

When a program broadcast in stereo is available, STEREO appears here.

When a program broadcast in second audio is available, 2ND AUD appears here.

When a program is available both in stereo and second audio, both STEREO and 2ND AUD appear here. Even though a program is avail- able in stereo or second audio, you still must program the VCR to receive or record the program. Follow the directions on page 45. NOTE: Although a program may be broadcast in both stereo and second audio, you cannot record in both stereo and second audio at the same time.

To record and play back programs broadcast in stereo, even if you have a Mono Speaker TV, just use one of the connections shown, then follow the steps on pages 45-47.

Stereo Amplifier

or Receiver

R

L

 

 

 

AUDIO

ANT

 

IN

 

 

L

 

 

OUT

IN

 

 

 

R

 

 

VIDEO

OUT

Audio cables from

OUT IN CH3 CH4

AUDIO OUT Jacks of

 

VCR to AUDIO IN Jacks

 

of Stereo Amplifier or

 

Receiver

 

Mono

Stereo

Monitor

Speaker TV

Speaker TV

TV

OR

OR

Monaural Sound

RF coaxial cable (supplied) from VCR’s

OUT Jack to TV’s ANTENNA IN Jack

Video cable from VIDEO OUT Jack of VCR to VIDEO IN Jack of monitor TV

Page 43 Page 45
Image 44
Page 43 Page 45
Contents VRZ262AT Dear Philips Magnavox product owner For Customer UseIntroduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVPlug in the TV and the VCR CH3Connections Recording/Viewing Any ChannelHookups With a Cable Box / Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups With a Stereo TV Turning on Your VCR 2Turn on the TVAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Enter a 0 before a single digit num- berDaylight-Saving Time Language Selection Setting the Remote to Operate a TV 2Find Remote Control Buttons VCR PLUS+/ENTER ButtonRemote Control Buttons cont’d On-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing Recording VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another One-Touch Recording Timer Recording DailyTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Checking or Cancelling Timer Recordings See page 48 for more hintsSetting Up the VCR Plus+ Programming System ChannelsSetting Up the VCR Plus+ Programming System cont’d Do each step within 60 seconds of the previous step Press the VCR PLUS+ /ENTER buttonTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication VCRRepeat Play Press the F.FWD/B button so that on appears besideWithin 10 seconds, use the Number buttons to enter Time SearchPress the VCR button Press the Time Search button Real-Time Counter Memory Special Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound System Understanding On-Screen DisplaysMulti-Channel Television Sound System cont’d Press the RECord/OTR button to start recordingPlease see additional notes on Hi-Fi Stereo Sound SystemPress the VCR button, then the Menu button Hi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel 03 orSpecifications Limited Warranty Video Cassette RecorderIndex VRZ262H1920.QX33 4/9/99 933 AM VRZ262H1920.QX33 4/9/99 933 AM Supplied Accessories
Top Page Image Contents