Graco 244561 important safety instructions Connect the Cables and Power Cord

Page 19

Installation

Connect the Cables and Power Cord

On the bottom of the controller, there are meter and solenoid cable connectors for three Fluid panels. The row of connectors marked 1A, 2A, and 3A are for solenoid cable connections. The row of connectors marked 1B, 2B, and 3B are for meter cable connections. Connect the cables as instructed below.

1.Connect the solenoid cable (E) between controller connector 1A and connector A on the first fluid panel.

2.Connect the meter cable (F) between controller connector 1B and connector B on the first fluid panel.

3.Repeat the cable connection for each of the fluid panels installed in the system (2A to A, 2B to B, etc.).

Aknockout, marked , is provided for a customer supplied power input (P) cable with strain relief or for wire conduit.

F

P	TI1438a
	E

FIG. 10

309301G

19

Image 19

Contents ProDispense 309301G Part No Electronic Preset Dispense SystemContents Parts ProDispense Controller Part No ProDispense System ComponentsWater/Antifreeze Grease/Paint MeterlessDure ConventionsFIRE, EXPLOSION, and Electric Shock Hazard High Pressure Fluid HAZARD/SKIN Injection Hazard Fluid Supply OverviewHow the ProDispense System Works UsageProDispense Controller Main ComponentsDisplay and EasyKey Pad Number Keys Previous Field Display Operation Mode Switch B and Key C Power Switch aRemote Operator Stations 244599 244600 244601 Fluid PanelsKey 246837 246838 246839 Key for FIG InstallationProDispense System Typical Installation Install the Fluid Supplies Fluid Panel 244601 Mount the Fluid Panels Connect the Air and Fluid Lines Fluid Panel 244599Fluid Panel Install the Remote Operator StationMount the Controller Connect the Cables and Power Cord Check the Resistance Ground the SystemConnect a Printer optional Connect to a PC or Alarm optionalBefore Beginning Operation ProDispense Rev StartupShutdown Pressure Relief ProcedureScreen Navigation Setup ModeTo enter Setup Mode To exit Setup ModeTo setup the system System Setup ScreenTo set up the fluids Fluid Setup ScreenFluid Panel Meter Type Factor Cc/pulse To calibrate a meter Recipe Setup ScreenTo setup the recipes Calibrate Meter ScreenRecipe Dispense Dispense ModeRun Screen Idle, Dispense, and Alarm StatusRecipe Dispense Fluid Dispense Fluid DispenseFluid Totals Fluid Totals ScreenInvalid K-factor Alarm Alarm History ScreenOut of Tolerance Alarm Dispense Timeout AlarmAutomatic Dispense Operation ProceduresLoading Fluid Lines Manual DispenseEmergency Stop Purging FluidProblem Cause Solution TroubleshootingRemoving and Installing Controller ServiceTo remove controller To install controller Replacing Display Board Replacing Membrane Replacing DisplayReplacing Main Board Replacing Power Supply Replacing Fluid Panel Junction Box Ti1404a Service Replacing Fluid Meter or Solenoid Servicing Fluid PanelTi1413a If replacing solenoid If replacing meterTi1412a Replacing Fluid Meter, Solenoid, or Dispense Valve Servicing Fluid Panel 244601If replacing dispense valve Show meter removal Replacing Solenoid or Dispense Valve Service 309301G Replacing Fluid Meter, Solenoid, or Dispense Valve Show meter removal Control Box Wiring Chart Wiring ChartsWire / Harness Connection Color Function Color Function Wire / HarnessHarness Connection Color Function Fluid Panel Wiring ChartFluid panels Field Wiring Chart Output Accessories Wiring ChartHarness Connection Color Function Connector-Pin Service 309301G Part No , Controller PartsDescription Qty Item 18 Cover Assembly Part No , Fluid Panel Ti1322a 10, 11, 12 19, 23, 24 Ti1324a Part No , Fluid Panel Qty Description309301G Power Requirements Technical DataMeter-less Flow meter supplied by user Wetted Parts Accessories and KitsGraco Information Graco Standard WarrantyToll Free, 612-623-6921, 612-378-3505 Fax