Graco 244561 important safety instructions FIRE, EXPLOSION, and Electric Shock Hazard

Page 6

WARNING

WARNING

FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in fire, explosion or electric shock.

•Installation and service of electrical components must be completed by a qualified electrician.

•Do not install the ProDispense controller, fluid panels, or remote operator station in a hazardous location.

•Ground the equipment. See Ground the System, page 20.

•If there is any static sparking while using equipment, stop dispensing immediately. Identify and correct the problem.

•Provide fresh air ventilation to avoid buildup of flammable fumes.

•Eliminate all ignition sources, such as cigarettes.

•Avoid spilling fluids onto electrical components.

•Turn off the ProDispense controller power switch before servicing equipment.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.

•Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer.

•Know the specific hazards of the fluid you are using.

•Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

•This equipment is for professional use only.

•Read all instruction manuals, tags, and labels before operating the equipment.

•Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

•Do not alter or modify this equipment.

•Check equipment daily. Repair or replace worn or damaged parts immediately.

•Do not exceed the maximum working pressure stated on the equipment or in the Technical Data, page 71.

•Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Techni- cal Data in all equipment manuals and the fluid manufacturer warnings.

•Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 180° F (82° C) or below -40° F (-40° C).

•Comply with all applicable local, state, and national fire, electrical, and safety regulations.

6

309301G

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Part No Electronic Preset Dispense System ProDispense 309301GContents Parts Meterless ProDispense System ComponentsWater/Antifreeze Grease/Paint ProDispense Controller Part NoConventions DureFIRE, EXPLOSION, and Electric Shock Hazard High Pressure Fluid HAZARD/SKIN Injection Hazard Usage OverviewHow the ProDispense System Works Fluid SupplyMain Components ProDispense ControllerDisplay and EasyKey Pad Number Keys Previous Field Display Power Switch a Operation Mode Switch B and Key CRemote Operator Stations Fluid Panels 244599 244600 244601Key 246837 246838 246839 Installation Key for FIGInstall the Fluid Supplies ProDispense System Typical InstallationFluid Panel 244599 Mount the Fluid PanelsConnect the Air and Fluid Lines Fluid Panel 244601Install the Remote Operator Station Fluid PanelMount the Controller Connect the Cables and Power Cord Ground the System Check the ResistanceConnect to a PC or Alarm optional Connect a Printer optionalBefore Beginning Operation Startup ProDispense RevPressure Relief Procedure ShutdownTo exit Setup Mode Setup ModeTo enter Setup Mode Screen NavigationSystem Setup Screen To setup the systemFluid Setup Screen To set up the fluidsFluid Panel Meter Type Factor Cc/pulse Calibrate Meter Screen Recipe Setup ScreenTo setup the recipes To calibrate a meterDispense Mode Recipe DispenseIdle, Dispense, and Alarm Status Run ScreenRecipe Dispense Fluid Dispense Fluid DispenseFluid Totals Screen Fluid TotalsDispense Timeout Alarm Alarm History ScreenOut of Tolerance Alarm Invalid K-factor AlarmManual Dispense Operation ProceduresLoading Fluid Lines Automatic DispensePurging Fluid Emergency StopTroubleshooting Problem Cause SolutionService Removing and Installing ControllerTo remove controller To install controller Replacing Display Board Replacing Display Replacing MembraneReplacing Main Board Replacing Power Supply Replacing Fluid Panel Junction Box Ti1404a Service Servicing Fluid Panel Replacing Fluid Meter or SolenoidTi1413a If replacing meter If replacing solenoidTi1412a Servicing Fluid Panel 244601 Replacing Fluid Meter, Solenoid, or Dispense ValveIf replacing dispense valve Show meter removal Replacing Solenoid or Dispense Valve Service 309301G Replacing Fluid Meter, Solenoid, or Dispense Valve Show meter removal Wiring Charts Control Box Wiring ChartWire / Harness Connection Color Function Wire / Harness Color FunctionFluid Panel Wiring Chart Harness Connection Color FunctionFluid panels Accessories Wiring Chart Field Wiring Chart OutputHarness Connection Color Function Connector-Pin Service 309301G Parts Part No , ControllerDescription Qty Item 18 Cover Assembly Part No , Fluid Panel Ti1322a 10, 11, 12 19, 23, 24 Ti1324a Part No , Fluid Panel Description Qty309301G Technical Data Power RequirementsMeter-less Flow meter supplied by user Accessories and Kits Wetted PartsGraco Standard Warranty Graco InformationToll Free, 612-623-6921, 612-378-3505 Fax

244561 specifications

The Graco 244561 is a highly regarded airless paint sprayer designed for both professional contractors and DIY enthusiasts. It is particularly known for its efficiency and versatility, making it suitable for a wide range of painting projects. This model offers several features that stand out in its class, ensuring that users achieve a high-quality finish with minimal effort.

One of the main features of the Graco 244561 is its powerful motor, which delivers consistent pressure for a smooth and even paint application. With a flow rate that can handle up to 0.42 gallons per minute, this sprayer is capable of quickly covering large areas, making it ideal for both interior and exterior projects. The robust design allows for the use of various paint types, including latex and oil-based finishes, giving users flexibility in their material choices.

The Graco 244561 also incorporates advanced technologies aimed at enhancing user experience and improving results. One of these is the Reverse-A-Clean feature, which enables users to easily clear clogs by reversing the flow of paint through the spray tip. This saves time and frustration, allowing users to get back to painting quickly. Additionally, the SmartControl technology ensures a consistent spray pattern at any pressure level, providing control over the finish and ensuring professional quality results.

The sprayer comes with a variety of accessories, including a spray tip that allows for different spray patterns and sizes. This ensures versatility in application, whether you are working on cabinets, walls, fences, or outdoor furniture. The adjustable pressure control also allows users to customize their spray settings based on the project, making it easier to work on intricate details or larger surfaces.

Durability is another key characteristic of the Graco 244561. Built with high-quality materials, this sprayer is designed to withstand the rigors of regular use in various environments. The compact and lightweight design also enhances portability, making it easy to transport from one job site to another.

In conclusion, the Graco 244561 airless paint sprayer is a powerful and versatile tool that caters to a wide array of painting needs. With its efficient motor, innovative technologies, and durable design, it promises excellent performance and reliability for both professionals and DIYers alike. Whether tackling a small home improvement project or a larger commercial job, the Graco 244561 stands out as a reliable choice that combines quality with user-friendliness.
Top Page Image Contents