Oricom 200 manual Troubleshooting, Problem Possible causes

Page 21

 

 

 

TROUBLESHOOTING

19

 

 

 

 

 

 

Problem

 

Possible cause(s)

 

 

 

 

 

 

 

The red power lights do not turn on when you plug

1.

Check if the units are properly connected to the power supply.

 

 

in the power.

2.

Check if the power is turned on. If not, Press [ ] to turn on the power.

 

The green Link light on the Parent Unit is flashing

1.

You may have moved out of range. Move closer to the Baby Unit and wait 5

 

and cannot hear the sounds from your baby's

 

seconds for the Link to establish.

 

 

2.

You may need to re−establish the Link between the two units. Turn both units

 

room.

 

 

off by pressing and holding the [ ] and then turn on again by pressing the [ ].

 

 

 

 

 

 

 

 

 

Can't hear your baby on the Parent Unit but the

Check if the volume is turned up on the Parent Unit.

 

 

Link light is still glowing steadily.

 

 

 

 

 

 

The battery icon on the Display is flashing on the

Your re-chargeable batteries are running low. Return the Parent Unit to the

 

Parent Unit.

Charger Pod to recharge them.

 

1.The batteries in the parent unit are not fully charged. Charge the parent unit for 14 hours before use.

2.The power to the baby unit may be turned off or disconnected, and or the Baby unit may be turned off. Reconnect the AC power adaptor to the baby unit and or turn on the baby unit.

3.You may have to re-establish the link between the two units. You will need to remove the batteries from the parent unit and register the parent unit back to the baby unit by following the instructions below:

Two horizontal bars flash centre of the display on

A. Ensure batteries are removed from the Parent unit (and baby unit if fitted) and the

the parent unit and "Not Linked" is shown.

AC power plug is disconnected from the Baby unit). Press and hold the [ ] on

 

the BABY unit then plug in the AC power plug, after 2 seconds, when the baby

 

unit night-lights flash release the [

] button;

 

B. Press and hold the [ ] on the PARENT unit then insert the batteries, after

 

2 seconds, the parent unit will sound an alert and the level indication red

 

LED’s will flash, then release the [

] button;

 

C. After a few seconds, the PARENT unit will give a confirmation tone and the

 

units will be re-linked and ready to use.

 

NOTE: Steps A and B need to be performed within 50 secs.

A high pitched ear piercing noise will be heard

Check if the Parent and Baby Units are too close together. Move them further apart.

from the units (feedback).

 

 

Image 21
Contents Baby Monitor Table of Contents Power requirements Cleaning and care Battery requirementsInstallation Pack ContentsGetting Started For the Baby Unit Baby unit Sender Your Baby MonitorLeft view of baby unit Belt Clip Volume Up/Down KeysParent unit Receiver 11 DC 6V inputLink Light Charger PodTalk key Charging LightLCD Display of Baby Monitor Baby UnitParent Unit Adjusting Volume Power On/OffBasic Operation MonitoringPaging Baby alertNight light LullabyTemperature ClockTime for a Feed Talk to your Baby Low BatteryOut of Range TorchCharging the Battery Night light Setting Menu SettingsLullaby Setting Sensitivity SettingTemperature Setting Sound Alert SettingAdjust Volume Set On or OffSet desired baby room temperature range Clock SettingSet temperature alert Set temperature alert volumeFeed Time Setting Set the timeSet the hour format Set Alarm on or off Language SettingSet Alarm Volume Set the first or next feed timeProblem Possible causes TroubleshootingFeature Specifications Product SpecificationsWarranty Australia GuaranteeAustralia Customer Support