Britax LATCHANCHOR manual Rear Facing Lap-Shoulder Belt Installation, See

Page 14

Installation:RearFacing

Rear Facing Lap-Shoulder Belt

 

Installation

 

1 Recline child restraint as necessary to align

 

leveling line horizontal with the ground.

 

IMPORTANT: Only use super recline

 

mode if necessary to obtain proper

 

angle, based on vehicle seat contour

A

(see page 29).

 

2 Unhook hook and loop attachments on the front edge of the cover, then pull the stabilizing bar out completely. Pull stabilizing bar upward until it clicks into position (fig. A).

IMPORTANT: Stabilizer bar

must

B

always be extended when seat is

rear

facing.

NOTE: Do not reattach cover with hook and loop until seat belt has been

routed.

3 Place the child restraint rear facing on the vehicle seat.

4 Fully extend the vehicle belt, then hold

C

the lap and shoulder sections together.

 

Keep the sections together as you pass the seat belt through the closest rear facing belt slot (fig. B).

5Route belt in front of the buckle strap, then through the second rear facing belt slot (fig. B).

6Fasten the seat belt, then verify that the seat belt is not twisted (fig. C).

13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Anch on Side Table of Contents Introduction Important Notes Safety Information Safety Information Child Restraint Features Harness Guard* not shown Vehicle Safety Belts Important Some vehicles have no seatingArea Vehicle Seating Positions Installation Rear Facing Removal Rear Facing Lap-Shoulder Belt Installation SeeClick is heard fig. E Rear Facing Lap Belt Installation Installation Rear Facing Switching the Latch Connectors Installation Forward Facing Forward Facing Installation with LatchRemoval Belt Installation If stabilizing bar is extendedSee Checking Buckle Position on Forward Facing Lap Belt Installation Checking Buckle Position Forward Facing Installation Installation In AircraftRear Facing Installation Versa TetherTM Forward Facing Versa-TetherVersa Tether TM Releasing the Versa-TetherRear Facing Versa-Tether Using the Tether Connector Strap rear facing only Recline Adjustment Fastening the Buckle Using the BuckleUsing the Chest Clip Releasing the BuckleSecuring Your Child See Checking Harness Height on Checking Harness Height To Check Harness HeightAdjusting Harness Height Harness Height AdjustmentBelly Pad Removal Care and MaintenanceCover Removal Refitting the CoverBuckle Removal Rethreading the BuckleCleaning the Harness Cleaning the CoverCleaning the Shell Cleaning the Buckle Thoroughly Rinse using warm water fig. BWarranty Limited ONE-YEAR WarrantyLimitation of Damages Registration Information Fill out the registration card and mail it in today

LATCHANCHOR specifications

The Britax LATCHAnchor is a state-of-the-art car seat installation system designed to simplify the process of securing your child's car seat while enhancing safety and convenience. The LATCH system—an acronym for Lower Anchors and Tethers for Children—was developed to provide a standardized method of attaching car seats to vehicles, ensuring a secure fit without the need for seat belts. The Britax LATCHAnchor exemplifies this system with its innovative and user-friendly design.

One of the standout features of the Britax LATCHAnchor is its easy-to-use installation mechanism. The system includes lower anchors built into the car seat, which connect effortlessly to the vehicle's designated LATCH anchors located in the seat. This design minimizes the chances of user error during installation, as it provides a secure and stable attachment point for the car seat. Additionally, the LATCHAnchor assists parents in achieving a proper installation—reducing the likelihood of improper attachment, which could compromise safety in the event of a collision.

Safety is a top priority, and the Britax LATCHAnchor incorporates advanced safety technologies to protect young passengers. The car seats are designed with energy-absorbing foam and side impact protection features, which work together to cushion and shield children in the event of an accident. The tether system further enhances safety by reducing seat rotation during a crash, thus providing additional security for the child.

In addition to safety and ease of use, the Britax LATCHAnchor boasts noteworthy flexibility. It is compatible with a variety of Britax car seat models and adapts to different vehicle types, making it a versatile option for families. The adjustable straps allow for a snug fit in different seating configurations, ensuring that parents can achieve the best installation possible.

Another significant advantage of the LATCHAnchor system is its convenient storage design. The LATCH connectors can easily be stored within the seat shell when not in use, keeping them tidy and preventing loss. This thoughtful design feature ensures that installation remains a hassle-free experience for parents.

The Britax LATCHAnchor perfectly embodies a blend of cutting-edge technology, user-focused design, and unparalleled safety features. By prioritizing ease of installation, adaptability, and safety, Britax continues to set the standard in child passenger safety. With the LATCHAnchor, parents can confidently transport their little ones, knowing they have chosen a reliable and meticulously engineered solution for their car seat needs.
Top Page Image Contents