Motorola MTM5400 installation manual Selecting an Antenna Site

Page 76

76

MTM5400 Mobile Terminal Installation Manual

INSTALLATION

 

 

 

Vehicle Antenna Installation

Mobile Radio Operation and EME Exposure

To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced in this document, transmit only when people inside and outside the vehicle are at least the minimum distance away from a properly installed, externally- mounted antenna.The table below lists the minimum distance for several different ranges of rated radio power.

Table 18 Rated Power and Distance

Mobile Radio Rated Power

Minimum Lateral Distance

(see Note below)

from Vehicle Body

 

 

Less than 7 Watts

20 Centimetres (8 inches)

 

 

7 to 15 Watts

30 Centimetres (1 Foot)

 

 

16 to 39 Watts

60 Centimetres (2 Feet)

 

 

40 to 110 Watts

90 Centimetres (3 Feet)

 

 

If you are not sure of the rated power of your radio, contact your Motorola representative or dealer and supply the radio model number found on the radio model label. If you cannot determine the rated power out, then assure 90 cm (3 feet) separation from the body of the vehicle.

Selecting an Antenna Site

1.Install the vehicle antenna external to the vehicle and in accordance with:

a.The requirements of the antenna manufacturer/supplier

b.The requirements of the vehicle manufacturer

2.The best mounting location for the antenna is in the centre of a large, flat conductive surface. In almost all vehicles, mounting the antenna in the centre of the roof will satisfy these requirements. A good alternate location is in the centre of the trunk lid. If you use the trunk lid, ensure that the trunk lid is grounded by connecting grounding straps between the trunk lid and the vehicle chassis.

3.Ensure the antenna cable can be easily routed to the radio. Ensure that the antenna cable is routed separately and not in parallel to any other vehicle wiring or mobile radio cable wiring.

It is recommended to mount the antenna outside the vehicle. Also make sure your power cable is not placed with the antenna in parallel. Interference can cause radio to hang.

4.Check the antenna location for any electrical interference according to vehicle manufacturer requirements.

5.Make sure the mobile radio antenna is installed at least 30 centimeters (1 foot) away from any other antenna on the vehicle.

Image 76
Contents @68015000181@ Page Copyright CopyrightsComputer Software Copyrights TrademarksThis page Intentionally Left Blank Important Safety Information Icon ConventionsPage Document History Edition Description DateThis page Intentionally Left Blank Contents DC Power Cable Installation Terminal InstallationData Expansion Head Enhanced Installation IntroductionConnectors and Pin Assignment of the Radio Vehicle Antenna InstallationExternal Speaker Installation Product Specific InformationThis page Intentionally Left Blank Scope Scope of This ManualInstallation Instructions MTM5400 Manuals and User GuidesWarranty and Service Support Service Information Europe, Middle East and Africa Region Emea Systems Support Centre EsscEmea Systems Component Centre Escc List of Telephone NumbersParts Identification and Ordering Updated Versions of this ManualEmea Test Equipment Support Your Input Asia, Pacific Region Piece PartsTechnical Support Further Assistance from MotorolaWarranty and Repairs Latin America RegionThis page Intentionally Left Blank MTM5400 Mobile Terminal Model Information Model Information & AccessoriesSales Model Nomenclature Model Specifications Model DescriptionsAccessories-to-Model Chart AccessoriesPMLN5072A GMAE4253A GMAE4254AGMAE4255A GMAE4256AModel Information & Accessories Installation Introduction General InformationDC Power Cable Installation Installation Planning OptionInstallation Procedure Power Cable Routing into the Engine CompartmentPower Cable Assembly Terminal Installation Enhanced Control Head Installation Typical Control Head RemovalTrunnion Installation Installation PlanningInstallation Procedure Dashboard Installation Installing the Radio in an Automotive DashboardMounting the Radio in the Frame DIN Mount Kit Components Description Part Number Remove the Radio from the Frame Removing the Radio from the FrameInstallation Desktop InstallationPlanning Associated Components Description Part Number Desktop Mounting See for Part NumbersRemote Mount Installation Associated Components for Remote MountRemote Mount Trunnion Kit PMLN4912 DIN Mount Bracket Kit Installation Installing the Accessories Expansion Cable Adding Extra Connectivity to the Remote HeadMotorcycle Mount Enhanced Control Head Installation Motorcycle Mount Enhanced Control Head Front SideInstalling the Motorcycle Mount Enhanced Control Head Motorcycle InstallationUpward Movement Installation of the Motorcycle Mount Telco Cable PMKN4030 Mechanical PartsInstallation Data Expansion Head Enhanced with 3rd Party Control Head DataTerminal AuxData Box Radio TransceiverJunction Box Installation GeneralService ConnectionsConnection Plan for the Speaker Connection Plan for the Junction Box Accessory TerminalSpeaker Connection Plan for the Alarm Relay AlarmConnection Plan for the Emergency Switch ExternalConnection Plan for Accessory Connector Kit HLN9457 Connection Plan for External PTTUse the Data Expansion Head Wire UART1TXDUART1RXD UART1RTSPin Function Description Accessory Connection Plan Re-crimp Procedure Pin Telco Connector Remote Head Enhanced Front View and Connector LocationPin subD Connector 10-Pin Telco ConnectorOnoffcontrol FlashmodeIntmic GroundConnector and Pin Assignment of the Enhanced Control Head Telco Connector Pin Function Description Audio +BUS + Audio25-Pin Back Connector Function Description Default Connecting Cable Motorcycle Mount Telco Cable Part Number PMKN4030 Length 2.3 m 7.55 feetAccessories Expansion Cable, Connector Pin Function Signal SubD 25 PosCustomised Wire Color Mobile Microphone Port MMPRED / Black Brown / White RTS RED / White CTS Orange / WhiteYellow / White Radio-to-Junction Box Part Number PMKN4101 Length 6 m 19.69 feetData Expansion Head Enhanced Radio-to-Data Device Standardized RS232 Cable Data Expansion Head Enhanced Radio-to-Fist Microphone Operation Making Connections Removing the Existing Coiled Cord CableInstallation Cable Connectivity Radio-to-Data Device Active Data CablePin Assignment Active Data Cable PMKN4104 Selecting an Antenna Site Antenna Installation Procedure Completing the InstallationExternal Speaker Installation Mounting the Speaker under the DashboardAppendix Equipment Electrical RatingsFuse Identification