Extension Placement Guide, Installation

Extension Placement Guide

Extension Placement Guide for Premier Gateway Model G150

Note: Each G5.5 Kit contains two extensions Note: Each G12.5 Kit contains one extension

Width Opening		Extensions		What You Need	Placement
29” – 31 ½”		Basic Gate		No extensions
31	½” - 34 ½”	Included with Gate		Gate + 1 extension	-on one end
34	½” – 37”			Gate + 2 extensions	-1 on each end
37” – 40”		1	G5.5 Kit	Gate + 3 extensions	-2 on one end; 1 on other end
40” – 42 ½”				Gate + 4 extensions	-3 on one end; 1 on other end
42	½” – 45”	2	G5.5 Kits	Gate + 5 extensions	-3 on one end; 2 on other end
45” – 47 ½”				Gate + 6 extensions	-3 on each end
47	½” – 49 ½”	1	G12.5	Gate + 3 extensions	-G12.5 on either end; 1 extension on each end
49	½” – 52”	1	G12.5 + 1 G5.5 Kit	Gate + 4 extensions	-1 G12.5 + 2 extensions on one end;
					1 extension on other end
52” – 55”				Gate + 5 extensions	-1 G12.5 + 2 extensions on one end;
					2 extensions on other end
55” – 57”		2	G12.5	Gate + 2 extensions	-1 G12.5 on each end
57” – 60”				Gate + 3 extensions	-1 G12.5 on each end; 1 extension on one end
60” – 62”				Gate + 4 extensions	-1 G12.5 + 1 extension on each end
62” – 65”		2	G12.5 + 1 G5.5 Kit	Gate + 5 extensions	-1 G12.5 + 1 extension on each end;
					1 extension on one end
65” – 68”				Gate + 6 extensions	-1 G12.5 + 2 extensions on each end
68” – 70”		2 G12.5 + 2 G5.5 Kits Gate + 7 extensions			-1 G12.5 + 2 extensions on each end;
					1 extension on other end
70” – 73 ½”				Gate + 8 extensions	-1 G12.5 + 3 extensions on each end

Each end may have no more than 4 extensions.

Extensions must be added as shown.

Installation

For further clarification, please see back of user guide for corresponding drawings.

1.The gate must be installed in a structurally sound opening. Never install between two railings or two stair posts.

Ensure mounting surface (wall, doorframe, stair post, etc.) is strong, rigid and is smooth, clean and grease free.

If mounting onto brick, drywall or other surfaces, an optional gate installation kit, wooden board mounted to the surface or additional hardware may be necessary to provide a solid, smooth surface.

Measure opening to determine if extensions are needed. Correct width will be reached by adjusting all 4 corner spindles. Each spindle adjusts individually and may be extended to varying lengths (up to 1¾” each) to allow for molding, uneven walls, etc.

If using gate on a stairway, it must be placed on the lowest stair on bottom.

2.Spindle attachment is different when using extensions and when not using extensions.

If no extension/s are used, slide top spindles (b) and bottom spindles (s) into spindle housing end with out tab (c). Push assembly into gate corners.

3.If using extension/s, (see Extension Placement

Guide) insert square extension tubes (j) into gate ends.

Connect the bar (k) to one upper extension housing (h) and one lower extension housing (i). Push assembly over extension tubes.

There should be no metal showing from extension tubes. It may be necessary to apply pressure to tubes to ensure they are fully inserted into gate ends. Slide top spindles (b) and bottom spindles (s) into extension tubes.

4.Note:

Spindle housings are not used if square extension tubes are necessary. If the housings have been inserted, remove with a screwdriver.

5.Center the gate in opening with bottom rail resting on floor. Gaps on each side should be equal.

Open the handle to the raised position by pressing the buttons (r) and lifting the handle (n) at the same time.

BUTTONS MUST ALWAYS BE PRESSED IN WHEN LIFTING HANDLE.

FAILURE TO DO SO WILL RESULT IN HANDLE MECHANISM BREAKING.