Canon FS 2710 manual Click the Clor Correction button, Set the threshold

Page 59

Procedure

Click the [Clor Correction] button.

•The threshold panel is displayed in the Color Correction dialog box.

•You can also click on the [Image] menu and select [Color Correction] to open the Color Correction dialog box.

Set the threshold.

The value set with the slide bar is displayed here. You can also enter a value (0 to

127)directly into the entry box without using the slider.

Drag the button right or left, or click the left or

right arrows to set the value.

Click on the [OK] button.

The changes will be reflected in the preview image.

59

59

Image 59

Contents Users Guide About the Conventions Used in this Guide How to Use this GuideWhere to Look Table of Contents Appendices Adjusting and Editing Scanned Images65 p p Control Panel FeaturesScan p Scanning ProceduresAdjust and Edit Scanned Images Plug-in module FS Special Features Selecting the Film Type p Installing Plug-in module FSQuick Start Instructions Starting Plug-in module FSSelect the area to be scanned by clicking and dragging Determining the type of image that is required. ppSpecifying the Area of the Image to be Scanned p Click on the Browser buttonSave to the target folder with the file name, file type, Scanning the Image pClick on the Scan button E P Operating Environment Installing Plug-in module FSE P Click the Install Software item E P ProcedureClick the Start Installation button at the lower right Install panel, select Photoshop LE and ScanExpert FSScanning Preparations Displaying the Plug-in module FS Control Panel E P Operating Procedures Selecting a Film Type Film CharacteristicsPlace the film in the scanner Previewing12bit Grayscale Mode FS2710 only Setting the Scan ModeBlack & White Mode 8bit Grayscale Mode36bit Color Mode FS2710 only 24bit Color ModeE P To Set the Scan Mode Selecting the Output Device Magnification and Resolution Setting the MagnificationOutput Device Resolution= 360 dpi, Magnification= 100% Slider Picture scanned with the 24bit Color mode may produce filesE P To Set the Magnification Factor Set the desired magnification factor on the control panelOutput Device Setting PreferencesOutput Device Setting Dialog Box Click on the OK button Output Device Settings Dialog BoxSelect the appropriate devices from the list E P Aspect Ratio Aspect Ratio Dialog Box Select the desired settingsUnit Dialog Box Unit Settings Dialog BoxE P Unit Set the file size and preview image save option Preview Window Settings Dialog BoxE P Preview Window Size Scan Settings Dialog Box E P Selecting the Scan SettingsClick on the Preferences menu and select Scan Settings Click the Yes button to reset the default settings E P Return to Default SettingsTo Set the Auto Eject Function Setting the Auto Eject FunctionPlace the mouse cursor inside the selection frame Verifying the Image Before ScanningTo Verify the Image E P Scanning Selection Tool Scan Area SettingsAdjust the size and position of the Selection Tool To Specify the Scan Area with the Selection ToolDrag the selection frame to the desired position ZoomingTo Zoom Click on the Zoom In buttonClick the mouse button Specify the Scan Area ScanningTo Initiate the Scan To Change the Orientation of an Image Rotating or Reversing Images Before ScanningClick the Save button Saving Scanned ImagesClick on the Photoshop LE File menu and select Save Adjusting and Editing Scanned Images Using color and film correction Optimum Adjustments for Image QualityColor Balance p Color CorrectionHistogram p Brightness/Contrast pThreshold p Gamma pPortion with Highlights Shadows Entire Image Color Correction Histogram SettingHow to Interpret Histograms How to Adjust HistogramsClick on the Auto Correction button E P To Adjust a Histogram AutomaticallyTo Adjusting a Histogram Manually Click the histogram tab and perform the histogram settingsAdjusting Contrast Color Correction Brightness and Contrast SettingsAdjusting Brightness Click on the Color Correction button in the control panel E P To Adjust the Brightness and ContrastClick the Brightness/Contrast tab to adjust the settings Color Correction Color Balance Click the OK button Color Correction with the Tone Curve Color Correction Tone Curve SettingsTone Curve Click on the Tone Curve tab and edit the tone curve E P To Edit the Tone Curve Gamma value Color Correction Gamma Value Settings Matching the Gamma Value to the Display Characteristics Click on the Gamma Value tab and edit the gamma value E P To Change the Gamma Value SettingsColor Correction Threshold Adjusts the brightness of dithered imagesSet the threshold Click the Clor Correction buttonManual Focus Film Correction Focus CorrectionAuto Focus Click the Auto Focus button to select automatic image focus Focus Setting Dialog BoxE P To Select Focus Click on the Film menu and select the Focus optionFilm Correction Exposure Adjustment Click on the Film menu and select Exposure 2700F Film Type SettingsAdjust the exposure Exposure Setting dialog box for FS2710Click on the Image menu and select the ColorSync option Auto Tone Correction ColorSyncTo Activate the ColorSync Function To Save Settings in a Settings File Saving / Recalling SettingsE P To Recall a Settings File Many special effects may be achieved with filters Editing Scanned ImagesSystem Requirements SpecificationsFunctional Specifications Ware TroubleshootingProblem Color correction function will not work ProblemResponse Error MessagesError Message Cause Mm Film List of Film Types 2700F onlyGlossary Positive Film ResolutionIX240 Film Negative FilmIndex a F SymbolsPict Index G STiff Index T ZCanon France S.A Canon Customer Support Help DeskCanon Europa N.V 1198 CDS Canon Inc