Canon FS 2710 manual Select the appropriate devices from the list, Click on the OK button

Page 27

S T E P 2

Select the appropriate devices from the list.

Output Device Settings Dialog Box

Select a device by clicking on its name. A check mark will appear beside the selected devices. Deselect a device by clicking its name again. You may not deselect [File (2720 dpi)]. Always ensure that a check mark appears beside this item.

You may specify a device that was not originally included in the list. Use the [Add] button to specify the name and resolution of a new device.

You can edit the settings specified for a new device with the [Edit] button.

You can delete a new output device from the list with the [Remove] button.

Click on the [OK] button.

27

27

Image 27

Contents Users Guide How to Use this Guide Where to LookAbout the Conventions Used in this Guide Table of Contents Appendices Adjusting and Editing Scanned Images65 p p Control Panel FeaturesScanning Procedures Adjust and Edit Scanned ImagesScan p Plug-in module FS Special Features Selecting the Film Type p Installing Plug-in module FSQuick Start Instructions Starting Plug-in module FSSelect the area to be scanned by clicking and dragging Determining the type of image that is required. ppSpecifying the Area of the Image to be Scanned p Click on the Browser buttonScanning the Image p Click on the Scan buttonSave to the target folder with the file name, file type, E P Installing Plug-in module FS E POperating Environment Click the Install Software item E P ProcedureClick the Start Installation button at the lower right Install panel, select Photoshop LE and ScanExpert FSScanning Preparations Displaying the Plug-in module FS Control Panel E P Operating Procedures Selecting a Film Type Film CharacteristicsPlace the film in the scanner Previewing12bit Grayscale Mode FS2710 only Setting the Scan ModeBlack & White Mode 8bit Grayscale Mode36bit Color Mode FS2710 only 24bit Color ModeE P To Set the Scan Mode Selecting the Output Device Setting the Magnification Output Device Resolution= 360 dpi, Magnification= 100%Magnification and Resolution Slider Picture scanned with the 24bit Color mode may produce filesE P To Set the Magnification Factor Set the desired magnification factor on the control panelSetting Preferences Output Device Setting Dialog BoxOutput Device Output Device Settings Dialog Box Select the appropriate devices from the listClick on the OK button E P Aspect Ratio Aspect Ratio Dialog Box Select the desired settingsUnit Settings Dialog Box E P UnitUnit Dialog Box Preview Window Settings Dialog Box E P Preview Window SizeSet the file size and preview image save option E P Selecting the Scan Settings Click on the Preferences menu and select Scan SettingsScan Settings Dialog Box Click the Yes button to reset the default settings E P Return to Default SettingsTo Set the Auto Eject Function Setting the Auto Eject FunctionVerifying the Image Before Scanning To Verify the ImagePlace the mouse cursor inside the selection frame E P Scanning Selection Tool Scan Area SettingsAdjust the size and position of the Selection Tool To Specify the Scan Area with the Selection ToolDrag the selection frame to the desired position ZoomingTo Zoom Click on the Zoom In buttonClick the mouse button Scanning To Initiate the ScanSpecify the Scan Area To Change the Orientation of an Image Rotating or Reversing Images Before ScanningSaving Scanned Images Click on the Photoshop LE File menu and select SaveClick the Save button Adjusting and Editing Scanned Images Using color and film correction Optimum Adjustments for Image QualityColor Balance p Color CorrectionHistogram p Brightness/Contrast pThreshold p Gamma pPortion with Highlights Shadows Entire Image Color Correction Histogram SettingHow to Interpret Histograms How to Adjust HistogramsClick on the Auto Correction button E P To Adjust a Histogram AutomaticallyTo Adjusting a Histogram Manually Click the histogram tab and perform the histogram settingsColor Correction Brightness and Contrast Settings Adjusting BrightnessAdjusting Contrast E P To Adjust the Brightness and Contrast Click the Brightness/Contrast tab to adjust the settingsClick on the Color Correction button in the control panel Color Correction Color Balance Click the OK button Color Correction Tone Curve Settings Tone CurveColor Correction with the Tone Curve Click on the Tone Curve tab and edit the tone curve E P To Edit the Tone CurveColor Correction Gamma Value Settings Matching the Gamma Value to the Display CharacteristicsGamma value Click on the Gamma Value tab and edit the gamma value E P To Change the Gamma Value SettingsColor Correction Threshold Adjusts the brightness of dithered imagesSet the threshold Click the Clor Correction buttonFilm Correction Focus Correction Auto FocusManual Focus Click the Auto Focus button to select automatic image focus Focus Setting Dialog BoxE P To Select Focus Click on the Film menu and select the Focus optionFilm Correction Exposure Adjustment Click on the Film menu and select Exposure 2700F Film Type SettingsAdjust the exposure Exposure Setting dialog box for FS2710Auto Tone Correction ColorSync To Activate the ColorSync FunctionClick on the Image menu and select the ColorSync option To Save Settings in a Settings File Saving / Recalling SettingsE P To Recall a Settings File Many special effects may be achieved with filters Editing Scanned ImagesSpecifications Functional SpecificationsSystem Requirements Ware TroubleshootingProblem Color correction function will not work ProblemError Messages Error Message CauseResponse Mm Film List of Film Types 2700F onlyGlossary Positive Film ResolutionIX240 Film Negative FilmIndex a F SymbolsPict Index G STiff Index T ZCanon France S.A Canon Customer Support Help DeskCanon Europa N.V 1198 CDS Canon Inc