Canon FS 2710 manual Saving Scanned Images, Click on the Photoshop LE File menu and select Save

Page 43

S T E P 3

Saving Scanned Images

Scanned images are saved in Photoshop.

Before you save a scanned image in Photoshop, you must select the file type for the saved image and select other settings. On the Macintosh the PICT and TIFF file types are commonly used for saving scanning images. The procedure below describes saving a scanned image as a PICT file with Photoshop LE. For details about using Photoshop LE, refer to the Photoshop LE electronic manual.

Procedure

Click on the Photoshop LE [File] menu and select [Save].

The Save dialog box will appear.

Select the destination (folder), file name, and file type for the image you are going to save.

In this example, PICT is selected as the file type.

Click the Save button.

The PICT File Options dialog box will open.

Click the radio buttons to select the options and click the [OK] button.

43

43

Image 43

Contents Users Guide Where to Look How to Use this GuideAbout the Conventions Used in this Guide Table of Contents Appendices Adjusting and Editing Scanned Images65 p p Control Panel FeaturesAdjust and Edit Scanned Images Scanning ProceduresScan p Plug-in module FS Special Features Selecting the Film Type p Installing Plug-in module FSQuick Start Instructions Starting Plug-in module FSSelect the area to be scanned by clicking and dragging Determining the type of image that is required. ppSpecifying the Area of the Image to be Scanned p Click on the Browser buttonClick on the Scan button Scanning the Image pSave to the target folder with the file name, file type, E P E P Installing Plug-in module FSOperating Environment Click the Install Software item E P ProcedureClick the Start Installation button at the lower right Install panel, select Photoshop LE and ScanExpert FSScanning Preparations Displaying the Plug-in module FS Control Panel E P Operating Procedures Selecting a Film Type Film CharacteristicsPlace the film in the scanner Previewing12bit Grayscale Mode FS2710 only Setting the Scan ModeBlack & White Mode 8bit Grayscale Mode36bit Color Mode FS2710 only 24bit Color ModeE P To Set the Scan Mode Selecting the Output Device Output Device Resolution= 360 dpi, Magnification= 100% Setting the MagnificationMagnification and Resolution Slider Picture scanned with the 24bit Color mode may produce filesE P To Set the Magnification Factor Set the desired magnification factor on the control panelOutput Device Setting Dialog Box Setting PreferencesOutput Device Select the appropriate devices from the list Output Device Settings Dialog BoxClick on the OK button E P Aspect Ratio Aspect Ratio Dialog Box Select the desired settingsE P Unit Unit Settings Dialog BoxUnit Dialog Box E P Preview Window Size Preview Window Settings Dialog BoxSet the file size and preview image save option Click on the Preferences menu and select Scan Settings E P Selecting the Scan SettingsScan Settings Dialog Box Click the Yes button to reset the default settings E P Return to Default SettingsTo Set the Auto Eject Function Setting the Auto Eject FunctionTo Verify the Image Verifying the Image Before ScanningPlace the mouse cursor inside the selection frame E P Scanning Selection Tool Scan Area SettingsAdjust the size and position of the Selection Tool To Specify the Scan Area with the Selection ToolDrag the selection frame to the desired position ZoomingTo Zoom Click on the Zoom In buttonClick the mouse button To Initiate the Scan ScanningSpecify the Scan Area To Change the Orientation of an Image Rotating or Reversing Images Before ScanningClick on the Photoshop LE File menu and select Save Saving Scanned ImagesClick the Save button Adjusting and Editing Scanned Images Using color and film correction Optimum Adjustments for Image QualityColor Balance p Color CorrectionHistogram p Brightness/Contrast pThreshold p Gamma pPortion with Highlights Shadows Entire Image Color Correction Histogram SettingHow to Interpret Histograms How to Adjust HistogramsClick on the Auto Correction button E P To Adjust a Histogram AutomaticallyTo Adjusting a Histogram Manually Click the histogram tab and perform the histogram settingsAdjusting Brightness Color Correction Brightness and Contrast SettingsAdjusting Contrast Click the Brightness/Contrast tab to adjust the settings E P To Adjust the Brightness and ContrastClick on the Color Correction button in the control panel Color Correction Color Balance Click the OK button Tone Curve Color Correction Tone Curve SettingsColor Correction with the Tone Curve Click on the Tone Curve tab and edit the tone curve E P To Edit the Tone CurveMatching the Gamma Value to the Display Characteristics Color Correction Gamma Value SettingsGamma value Click on the Gamma Value tab and edit the gamma value E P To Change the Gamma Value SettingsColor Correction Threshold Adjusts the brightness of dithered imagesSet the threshold Click the Clor Correction buttonAuto Focus Film Correction Focus CorrectionManual Focus Click the Auto Focus button to select automatic image focus Focus Setting Dialog BoxE P To Select Focus Click on the Film menu and select the Focus optionFilm Correction Exposure Adjustment Click on the Film menu and select Exposure 2700F Film Type SettingsAdjust the exposure Exposure Setting dialog box for FS2710To Activate the ColorSync Function Auto Tone Correction ColorSyncClick on the Image menu and select the ColorSync option To Save Settings in a Settings File Saving / Recalling SettingsE P To Recall a Settings File Many special effects may be achieved with filters Editing Scanned ImagesFunctional Specifications SpecificationsSystem Requirements Ware TroubleshootingProblem Color correction function will not work ProblemError Message Cause Error MessagesResponse Mm Film List of Film Types 2700F onlyGlossary Positive Film ResolutionIX240 Film Negative FilmIndex a F SymbolsPict Index G STiff Index T ZCanon France S.A Canon Customer Support Help DeskCanon Europa N.V 1198 CDS Canon Inc