Canon FS 2710 manual System Requirements, Functional Specifications

Page 68

S T E P 2

Appendices

Troubleshooting

Error Messages

List of Film Types

Glossary

Index

Customer Support Help Desk

p.69 p. 71 p. 72 p. 73 p. 75 p. 78

Specifications

System Requirements

Supported Computers:	Macintosh or Power Macintosh computers equipped with a CD-ROM
	drive and hard disk drive.

Memory Requirements:	12 MB

System Software:	System 7.1 or later

Supported Scanners:	CanoScan 2700F, CanoScan FS2710 Color Film Scanner

Functional Specifications

Interface:	Auto Detection of SCSI Scanner

Scan Modes:	Black & White, 8bit Grayscale, 12bit Grayscale, 24bit Color, 36bit Color

Tone Settings:	255	Gradations

Contrast Settings:	255	Gradations

Density Settings:	255	Gradations (only for Black & White mode)

Gamma Curve:	Gamma Curve May Be Edited

Scanning Resolution:	2720 dots per inch

		* These specifications are subject to change without notice.

Image 68

Contents Users Guide About the Conventions Used in this Guide How to Use this GuideWhere to Look Table of Contents Adjusting and Editing Scanned Images AppendicesControl Panel Features 65 p pScan p Scanning ProceduresAdjust and Edit Scanned Images Plug-in module FS Special Features Installing Plug-in module FS Quick Start InstructionsStarting Plug-in module FS Selecting the Film Type pDetermining the type of image that is required. pp Specifying the Area of the Image to be Scanned pClick on the Browser button Select the area to be scanned by clicking and draggingSave to the target folder with the file name, file type, Scanning the Image pClick on the Scan button E P Operating Environment Installing Plug-in module FSE P E P Procedure Click the Install Software itemInstall panel, select Photoshop LE and ScanExpert FS Click the Start Installation button at the lower rightScanning Preparations Displaying the Plug-in module FS Control Panel E P Operating Procedures Film Characteristics Selecting a Film TypePreviewing Place the film in the scannerSetting the Scan Mode Black & White Mode8bit Grayscale Mode 12bit Grayscale Mode FS2710 only24bit Color Mode 36bit Color Mode FS2710 onlyE P To Set the Scan Mode Selecting the Output Device Magnification and Resolution Setting the MagnificationOutput Device Resolution= 360 dpi, Magnification= 100% Picture scanned with the 24bit Color mode may produce files E P To Set the Magnification FactorSet the desired magnification factor on the control panel SliderOutput Device Setting PreferencesOutput Device Setting Dialog Box Click on the OK button Output Device Settings Dialog BoxSelect the appropriate devices from the list E P Aspect Ratio Select the desired settings Aspect Ratio Dialog BoxUnit Dialog Box Unit Settings Dialog BoxE P Unit Set the file size and preview image save option Preview Window Settings Dialog BoxE P Preview Window Size Scan Settings Dialog Box E P Selecting the Scan SettingsClick on the Preferences menu and select Scan Settings E P Return to Default Settings Click the Yes button to reset the default settingsSetting the Auto Eject Function To Set the Auto Eject FunctionPlace the mouse cursor inside the selection frame Verifying the Image Before ScanningTo Verify the Image E P Scanning Scan Area Settings Adjust the size and position of the Selection ToolTo Specify the Scan Area with the Selection Tool Selection ToolZooming To ZoomClick on the Zoom In button Drag the selection frame to the desired positionClick the mouse button Specify the Scan Area ScanningTo Initiate the Scan Rotating or Reversing Images Before Scanning To Change the Orientation of an ImageClick the Save button Saving Scanned ImagesClick on the Photoshop LE File menu and select Save Adjusting and Editing Scanned Images Optimum Adjustments for Image Quality Using color and film correctionColor Correction Histogram pBrightness/Contrast p Color Balance pGamma p Threshold pColor Correction Histogram Setting How to Interpret HistogramsHow to Adjust Histograms Portion with Highlights Shadows Entire ImageE P To Adjust a Histogram Automatically To Adjusting a Histogram ManuallyClick the histogram tab and perform the histogram settings Click on the Auto Correction buttonAdjusting Contrast Color Correction Brightness and Contrast SettingsAdjusting Brightness Click on the Color Correction button in the control panel E P To Adjust the Brightness and ContrastClick the Brightness/Contrast tab to adjust the settings Color Correction Color Balance Click the OK button Color Correction with the Tone Curve Color Correction Tone Curve SettingsTone Curve E P To Edit the Tone Curve Click on the Tone Curve tab and edit the tone curveGamma value Color Correction Gamma Value SettingsMatching the Gamma Value to the Display Characteristics E P To Change the Gamma Value Settings Click on the Gamma Value tab and edit the gamma valueAdjusts the brightness of dithered images Color Correction ThresholdClick the Clor Correction button Set the thresholdManual Focus Film Correction Focus CorrectionAuto Focus Focus Setting Dialog Box E P To Select FocusClick on the Film menu and select the Focus option Click the Auto Focus button to select automatic image focusFilm Correction Exposure Adjustment 2700F Film Type Settings Adjust the exposureExposure Setting dialog box for FS2710 Click on the Film menu and select ExposureClick on the Image menu and select the ColorSync option Auto Tone Correction ColorSyncTo Activate the ColorSync Function Saving / Recalling Settings To Save Settings in a Settings FileE P To Recall a Settings File Editing Scanned Images Many special effects may be achieved with filtersSystem Requirements SpecificationsFunctional Specifications Troubleshooting WareProblem Problem Color correction function will not workResponse Error MessagesError Message Cause List of Film Types 2700F only Mm FilmGlossary Resolution IX240 FilmNegative Film Positive FilmSymbols Index a FIndex G S PictIndex T Z TiffCanon Customer Support Help Desk Canon France S.ACanon Europa N.V 1198 CDS Canon Inc