Yamaha RX-V557 Press d to display the Speakers parameter, Press d to display SET/CANCEL

Page 25

7Press d to display the SPEAKERS parameter.

PRESET/CH

ENTER

A/B/C/D/E

8Press j / i to select the number of speakers you connected.

SPEAKERS..6spk

Choices

Display

Speakers

2spk

L C R

Front L/R

 

SL SB SR

 

3spk

L C R

Front L/R, Center

 

SL SB SR

 

4spk

L C R

Front L/R, Surround L/R

 

SL SB SR

 

5spk

L C R

Front L/R, Center, Surround L/R

SL SB SR

 

6spk

L C R

Front L/R, Center, Surround L/R,

Surround back

SL SB SR

9Press d to display SET/CANCEL.

PRESET/CH

ENTER

A/B/C/D/E

10Press j / i to select the desired setting.

BASIC SETUP

11Press ENTER to confirm your selection.

PRESET/CH

ENTER

A/B/C/D/E

If you selected SET, you hear a test tone from each speaker in turn. “CHECK:TestTone” appears in the front panel display for a few seconds, then “CHECK OK?”.

CHECK:TestTone

CHECK OK? YES

12Press j / i to select the desired setting.

CHECK OK? YES

YES To complete the setup process if the test tone levels from each speaker were satisfactory.

NO To proceed to the SP LEVEL speaker level adjustment menu to balance the level of each speaker.

13Press ENTER to confirm your selection.

PRESET/CH

ENTER

A/B/C/D/E

If you selected NO in step 12, the front speaker level adjustment display appears in the front panel display.

PREPARATION

>SET CANCEL

SET

To apply the settings you chose in steps

 

4 through 8.

CANCEL To cancel the setup without making any changes.

English

23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents RX-V557 Special Instructions for U.K. Model For U.K. customersContents Built-in 6-channel power amplifier FeaturesSound field features Other featuresInstalling batteries in the remote control Supplied accessoriesGetting Started Please check that you received all of the following partsFront panel Controls and FunctionsPRESET/TUNING Edit VolumeInput Mode Speakers A/BRemote control Using the remote control Front panel display LFE indicator 96/24 indicatorInput channel indicators/speaker indicators Zone 2 indicatorAC Outlets Rear panelSpeaker placement Speaker SetupOhms before using see Tighten the knob to secure the wireSpeaker connections Connect surround speakers 6, 7 to these terminals Front terminalsSubwoofer jack Surround Back terminalsConnections Before connecting componentsConnections for DVD playback Connecting video componentsConnecting to the Multi CH Input jacks Video AUX jacks on the front panel Connections for other video componentsConnections for audio components Connecting audio componentsInsert the cable Wire into the slot Connecting the FM and AM antennasClamp it with Pliers Snap the cover into placeConnecting the AC power cord Connecting the power supply cordAC Outlets Switched Memory back-upTurning on the power Speaker impedance settingPress STANDBY/ON to turn off the power Rotate Program to move through the menu and select SP IMPUsing the Basic Setup menu Basic SetupPress d to display the Speakers parameter Press d to display SET/CANCELPress j / i to select the number of speakers you connected Press Enter to confirm your selectionPerform the following steps after see To balance the speaker levelsPlayback Adjust the volume to the desired output levelBasic operations Select the input sourceTo adjust the tone To listen with headphonesSelect a sound field program if desired Silent CinemaSelecting Multi CH Input Selecting sound field programsPlaying video sources Background Front panel operationEnjoying multi-channel software Remote control operationAuto Auto Decoders select with jWhen you select the SUR. Standard program Press Select on the remote control to select the decoderWhen you select the SUR. Enhanced or Movie Theater program Enjoying 2-channel software in surroundListening to high fidelity stereo sound Direct Stereo This adjusts the level of compressionNight listening modes Downmixing to 2 channels Listening to unprocessed input signalsVirtual Cinema DSP Rotate Input to select the input source Selecting input modesDisplaying information about the input Source Automatic and manual tuning FM/AM TuningManual tuning Presetting stationsAutomatically presetting FM stations Hold down the button to continue searchingAutomatic preset tuning options Manually presetting stationsPress and hold Memory MAN’L/AUTO FM for more than 3 seconds Tune into a stationShows the displayed station has been stored as C3 Selecting preset stationsRepeat steps 1 to 5 to store other stations Select preset station E1 Exchanging preset stationsSee Selecting preset stations Press and hold PRESET/TUNING Edit for more than 3 secondsReceiving Radio Data System stations Do not press FREQ/TEXT until a Radio Data System indicator Changing the Radio Data System modeSelected program type appears in the front panel display PTY Seek functionEON function To cancel this functionRecording Special considerations when recording DTS softwareFor movie/video sources Sound Field Program DescriptionsSUR. Standard Hall in Vienna For music sourcesSetting the sleep timer Canceling the sleep timer Using the sleep timerAdvanced Operations Amount of timePress j / i to adjust the speaker output level Manually adjusting speaker levelsPress Enter when you have completed your adjustment Control range is from +10 dB to -10 dBSET Menu Using SET Menu Subwoofer phase Swfr Phase Speaker settings Aspeaker SETFront speakers Front Center speaker CenterSpeaker distance CSP Distance Speaker level BSP LevelUnit Unit Speaker distancesAudio delay A. Delay Audio settings Gaudio SETMuting type Mute TYP Tone bypass TC.BYPASSVideo conversion V. Conv Display settings Adisplay SET Dimmer DimmerParameter initialization CPARAM. INI Speaker B setting SP BAdvanced Setup menu is displayed in the front panel display Advanced Setup MenuPress STANDBY/ON to confirm your selection Factory presets Preset Advanced Setup menu itemsSpeaker impedance SP IMP Remote RemoteControl area Remote Control FeaturesControlling this unit Controlling other componentsRemote Control Code Default Settings Setting remote control codesPress Code SET using a ballpoint pen or similar object Transmit indicator on the remote control flashes twiceVCR Controlling other componentsClearing set up remote control codes Switching library codesEnter the code number 9991 or 9992 see the table below Enter the code numberZone System configuration and connections exampleZone 2 connections Standby Remote controlling ZoneSpecial considerations for DTS software To turn on all units the main unit and Zone 2 unitFor DVDs encoded in DTS For CDs encoded in DTSEditing Sound Field Parameters What is a sound field Changing parameter settingsUse PARAM. INI see Resetting parameters to the factory PresetsSound Field Parameter Descriptions INIT.DLY Initial delayDSP Level DSP level For 2ch Stereo Direct DirectFor 6ch Stereo Dimension DimensionCT Width Center width For DTS Neo6 Music Image Center imageGeneral TroubleshootingTroubleshooting Digital Output Tuner Remote controlAdvanced Setup menu appears in the front panel display Resetting the Factory PresetsRotate Program to move through the menu and select Preset Press Straight Effect to select the desired settingAudio formats GlossaryAudio information Sound field programsCinema DSP ITU-RComponent video signal Video signal informationComposite video signal Video signalSpecifications APPENDIX-i APPENDIX-ii APPENDIX-iii APPENDIX-iv APPENDIX-v All rights reserved
Top Page Image Contents