Yamaha RX-V557 owner manual Tuner, Remote control

Page 73

TROUBLESHOOTING

■Tuner

 

Problem

Cause

Remedy

Refer

 

to page

 

 

 

 

 

FM stereo reception is

The characteristics of FM stereo

Check the antenna connections.

19

 

noisy.

broadcasts may cause this problem

Try using a high-quality directional FM

 

 

 

when the transmitter is too far away or

antenna.

 

 

 

the antenna input is poor.

Use the manual tuning method.

34

 

 

 

 

There is distortion, and

There is multipath interference.

Adjust the antenna position to eliminate

—

 

clear reception cannot

 

multipath interference.

 

FM

be obtained even with a

 

 

 

good FM antenna.

 

 

 

 

The desired station

The signal is too weak.

Use a high-quality directional FM antenna.

19

 

cannot be tuned in with

 

Use the manual tuning method.

34

 

the automatic tuning

 

 

method.

 

 

 

 

 

 

 

 

 

Previously preset

This unit has been disconnected for a

Preset the stations again.

34

 

stations can no longer

long period.

 

 

 

be tuned in.

 

 

 

 

The desired station

The signal is weak or the antenna

Tighten the AM loop antenna connections

—

 

cannot be tuned in with

connections are loose.

and orient it for the best reception.

 

 

the automatic tuning

 

 

 

 

 

Use the manual tuning method.

34

 

method.

 

AM

There are continuous

Noises result from lightning,

Use an outdoor antenna and a ground wire.

—

 

crackling and hissing

fluorescent lamps, motors, thermostats

This will help somewhat, but it is difficult to

 

 

noises.

and other electrical equipment.

eliminate all noise.

 

 

 

 

 

 

 

There are buzzing and

A TV set is being used nearby.

Move this unit away from the TV.

—

 

whining noises.

 

 

 

■Remote control

Problem

Cause

Remedy

Refer to

page

 

 

 

The remote control

Wrong distance or angle.

The remote control will function within a maximum

7

does not work nor

 

range of 6 m and no more than 30 degrees off-axis

 

function properly.

 

from the front panel.

 

 

 

 

 

 

Direct sunlight or lighting (from an

Reposition this unit.

—

 

inverter type of fluorescent lamp, etc.) is

 

 

 

striking the remote control sensor of this

 

 

 

unit.

 

 

 

The batteries are weak.

Replace all batteries.

3

 

The remote control code was not correctly

Set the remote control code correctly using “LIST OF

58

 

set.

REMOTE CONTROL CODES” at the end of this

 

 

 

manual.

 

 

 

Try to set another code for the same manufacturer

58

 

 

using “LIST OF REMOTE CONTROL CODES” at

 

 

 

the end of this manual.

 

 

 

 

 

 

The remote control ID and this unit’s ID

Switch the library code.

60

 

do not match.

 

 

 

Even if the remote control code is

 

 

 

correctly set, there are some models that

 

 

 

do not respond to the remote control.

 

 

 

 

 

 

INFORMATION

ADDITIONAL

 

 

English

 

 

 

71

Page 72 Page 74
Image 73
Page 72 Page 74
Contents RX-V557 Special Instructions for U.K. Model For U.K. customersContents Built-in 6-channel power amplifier FeaturesSound field features Other featuresInstalling batteries in the remote control Supplied accessoriesGetting Started Please check that you received all of the following partsFront panel Controls and FunctionsPRESET/TUNING Edit VolumeInput Mode Speakers A/BRemote control Using the remote control Front panel display LFE indicator 96/24 indicatorInput channel indicators/speaker indicators Zone 2 indicatorAC Outlets Rear panelSpeaker placement Speaker SetupOhms before using see Tighten the knob to secure the wireSpeaker connections Connect surround speakers 6, 7 to these terminals Front terminalsSubwoofer jack Surround Back terminalsConnections Before connecting componentsConnections for DVD playback Connecting video componentsConnecting to the Multi CH Input jacks Video AUX jacks on the front panel Connections for other video componentsConnections for audio components Connecting audio componentsInsert the cable Wire into the slot Connecting the FM and AM antennasClamp it with Pliers Snap the cover into placeConnecting the AC power cord Connecting the power supply cordAC Outlets Switched Memory back-upTurning on the power Speaker impedance settingPress STANDBY/ON to turn off the power Rotate Program to move through the menu and select SP IMPUsing the Basic Setup menu Basic SetupPress d to display the Speakers parameter Press d to display SET/CANCELPress j / i to select the number of speakers you connected Press Enter to confirm your selectionPerform the following steps after see To balance the speaker levelsPlayback Adjust the volume to the desired output levelBasic operations Select the input sourceTo adjust the tone To listen with headphonesSelect a sound field program if desired Silent CinemaSelecting Multi CH Input Selecting sound field programsPlaying video sources Background Front panel operationEnjoying multi-channel software Remote control operationAuto Auto Decoders select with jWhen you select the SUR. Standard program Press Select on the remote control to select the decoderWhen you select the SUR. Enhanced or Movie Theater program Enjoying 2-channel software in surroundListening to high fidelity stereo sound Direct Stereo This adjusts the level of compressionNight listening modes Downmixing to 2 channels Listening to unprocessed input signalsVirtual Cinema DSP Rotate Input to select the input source Selecting input modesDisplaying information about the input Source Automatic and manual tuning FM/AM TuningManual tuning Presetting stationsAutomatically presetting FM stations Hold down the button to continue searchingAutomatic preset tuning options Manually presetting stationsPress and hold Memory MAN’L/AUTO FM for more than 3 seconds Tune into a stationShows the displayed station has been stored as C3 Selecting preset stationsRepeat steps 1 to 5 to store other stations Select preset station E1 Exchanging preset stationsSee Selecting preset stations Press and hold PRESET/TUNING Edit for more than 3 secondsReceiving Radio Data System stations Do not press FREQ/TEXT until a Radio Data System indicator Changing the Radio Data System modeSelected program type appears in the front panel display PTY Seek functionEON function To cancel this functionRecording Special considerations when recording DTS softwareFor movie/video sources Sound Field Program DescriptionsSUR. Standard Hall in Vienna For music sourcesSetting the sleep timer Canceling the sleep timer Using the sleep timerAdvanced Operations Amount of timePress j / i to adjust the speaker output level Manually adjusting speaker levelsPress Enter when you have completed your adjustment Control range is from +10 dB to -10 dBSET Menu Using SET Menu Subwoofer phase Swfr Phase Speaker settings Aspeaker SETFront speakers Front Center speaker CenterSpeaker distance CSP Distance Speaker level BSP LevelUnit Unit Speaker distancesAudio delay A. Delay Audio settings Gaudio SETMuting type Mute TYP Tone bypass TC.BYPASSVideo conversion V. Conv Display settings Adisplay SET Dimmer DimmerParameter initialization CPARAM. INI Speaker B setting SP BAdvanced Setup menu is displayed in the front panel display Advanced Setup MenuPress STANDBY/ON to confirm your selection Factory presets Preset Advanced Setup menu itemsSpeaker impedance SP IMP Remote RemoteControl area Remote Control FeaturesControlling this unit Controlling other componentsRemote Control Code Default Settings Setting remote control codesPress Code SET using a ballpoint pen or similar object Transmit indicator on the remote control flashes twiceVCR Controlling other componentsClearing set up remote control codes Switching library codesEnter the code number 9991 or 9992 see the table below Enter the code numberZone System configuration and connections exampleZone 2 connections Standby Remote controlling ZoneSpecial considerations for DTS software To turn on all units the main unit and Zone 2 unitFor DVDs encoded in DTS For CDs encoded in DTSEditing Sound Field Parameters What is a sound field Changing parameter settingsUse PARAM. INI see Resetting parameters to the factory PresetsSound Field Parameter Descriptions INIT.DLY Initial delayDSP Level DSP level For 2ch Stereo Direct DirectFor 6ch Stereo Dimension DimensionCT Width Center width For DTS Neo6 Music Image Center imageGeneral TroubleshootingTroubleshooting Digital Output Tuner Remote controlAdvanced Setup menu appears in the front panel display Resetting the Factory PresetsRotate Program to move through the menu and select Preset Press Straight Effect to select the desired settingAudio formats GlossaryAudio information Sound field programsCinema DSP ITU-RComponent video signal Video signal informationComposite video signal Video signalSpecifications APPENDIX-i APPENDIX-ii APPENDIX-iii APPENDIX-iv APPENDIX-v All rights reserved
Top Page Image Contents